Rubber & FoamSKU IP-SLP-4.5X5.2-BLACK
Silicone L Profile – 4.5mm x 5.2mm – 25m Coil
This silicone L profile 4.5mm x 5.2mm is a miniature solid angle trim with a 2.0mm base leg and a slim upright that tapers from 1.5mm to 1.3mm at the tip. It protects, seals and finishes very fine edges on sheet metal, glass, instrument cases and small enclosures. You get one continuous 25m coil (£27.00 per metre) in a choice of seven colours, all at the same price.
At a glance
- Miniature L angle: 4.5mm wide x 5.2mm high, solid section
- 2.0mm base leg; 1.5mm upright tapering to 1.3mm over its top 2.0mm
- 60 Shore A silicone: flexible enough to follow gentle curves
- Compound meets FDA 21 CFR 177.2600 and EC 1935/2004, and is WRAS approved
- Works from -50°C to +180°C; resists UV, ozone and weathering
- Seven colours for colour-coding or matching equipment
- Held in stock in all seven colours
Typical uses
- Edge protection on thin sheet metal, acrylic and glass where space is tight
- Small corner seals and raised lips on instrument cases, control panels and HVAC covers
- Trims on food and drink processing equipment
- Potable water equipment that needs a WRAS approved silicone
- Finishing strips in laboratories, cleanrooms and electronics enclosures
- Colour-coded edges for identifying zones, lines or equipment
Technical drawing
![]()
Specification
| Property | Value | Test method |
|---|---|---|
| Profile type | Solid L (angle), tapered upright leg | – |
| Overall width (base) | 4.5 mm | Nominal |
| Overall height (upright) | 5.2 mm | Nominal |
| Base leg thickness | 2.0 mm | Nominal |
| Upright leg thickness | 1.5 mm at the root, tapering to 1.3 mm at the tip | Nominal |
| Taper length | Top 2.0 mm of the upright | Nominal |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Coil length | 25 m, one continuous length | – |
| Material | Silicone rubber | – |
| Hardness | 60 Shore A | DIN ISO 48-4 |
| Density | 1.15 g/cm³ | DIN EN ISO 1183-1 A |
| Tensile strength | 11 N/mm² (11 MPa) | ISO 37 Type 1 |
| Elongation at break | 550 % | ISO 37 Type 1 |
| Tear strength | 26 N/mm (26 kN/m) | ASTM D624 Die B |
| Compression set, 22 h at 175°C | 31 % | DIN ISO 815-1 Type B, Method A |
| Rebound resilience | 59 % | ISO 4662 |
| Working temperature | -50°C to +180°C | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, cosmic and ionising radiation, corona discharge | – |
| Colours | Black, blue, green, red, translucent, white, yellow | – |
| Price per metre | £27.00 inc VAT (£675.00 per 25 m coil) | – |
Materials and compliance
The profile is extruded from a single silicone rubber compound. For this exact profile the manufacturer's data states:
- FDA 21 CFR 177.2600: the compound complies for repeated-use rubber articles in contact with food.
- EC 1935/2004: the compound complies with the EU framework regulation for food-contact materials.
- WRAS approved material: suitable for use with potable (drinking) water.
- Free from TSE/BSE-derived products and free from phthalates.
These approvals cover the compound. Check that the finished assembly meets the rules for your own application.
Which one do I need?
| Profile | Choose it when |
|---|---|
| Silicone L 4.5mm x 3.7mm | You want the same narrow base with a lower 3.7mm upstand |
| Silicone L 4.5mm x 5.2mm (this item) | You want a 4.5mm base with a taller, slim 5.2mm leg |
| Silicone L 5mm x 6mm | You want a slightly larger 6mm return leg |
| Silicone L 6.2mm x 5.2mm | You want the same height with a wider 6.2mm base for more bonding area |
How much do I need?
Measure each edge to be trimmed and add about 5% for corners and trimming. For example, twelve instrument-case lids, each 250mm x 200mm with all four edges trimmed, need 12 x 0.9m = 10.8m, or about 11.4m with the allowance. One 25m coil covers them with over 13m to spare.
Fitting tips
- Clean and degrease the edge first. Silicone sealants only bond to dry, oil-free surfaces.
- At this small size, a thin bead of silicone or polyurethane sealant holds the trim far better than a push fit alone.
- Cut slightly over length with a sharp blade and trim back once the sealant has cured.
- Use a mitre block for neat 45° corners on small lids and covers.
Complete your project
Questions
How do I fit it?
Sit the inside corner of the L against the edge you are protecting and bond it with a thin bead of silicone or polyurethane sealant. With legs this small, a push fit on its own only suits light, temporary edge protection.
Will it fit my edge?
It is a solid angle, not a clip-on channel, so it does not grip a set panel thickness. It suits any square edge where a 4.5mm wide base and a 5.2mm high upstand will look right. Check the drawing above against your part.
How do I cut and join it?
Cut it cleanly with a sharp knife or scissors. Make corners as 45° mitres, or as butt joints sealed with a dab of silicone sealant. Silicone cannot be glued with ordinary contact adhesives.
What temperatures can it take?
It works continuously from -50°C to +180°C, so it suits ovens, heated cabinets, cold stores and outdoor kit.
Is it safe for food and drinking water?
The compound meets FDA 21 CFR 177.2600 and EC 1935/2004 for food contact and is a WRAS approved material for potable water.
Can I use it outdoors?
Yes. Silicone resists UV, ozone and weathering, and it stays flexible in frost.
Is every colour the same price?
Yes. All seven colours are £675.00 per 25m coil, which works out at £27.00 per metre.
Can I buy a shorter length?
This listing is for full 25m coils. Contact our team if you need a different quantity.
Need help choosing a size? Contact our team on +44 1282 277786 or sales@industrial-polymers.co.uk.
Product details
| SKU | IP-SLP-4.5X5.2-BLACK |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone L Profile – 4.5mm x 5.2mm – 25m Coil