Rubber & FoamSKU IP-SILP-7.5X5.5-BLACK
Silicone L Profile – 7.5mm x 5.5mm – 25m Coil
A heavy-section solid silicone L profile, 7.5mm wide x 5.5mm high. Its upright is a thick 5.0mm block and its base is 2.0mm, so one face of the corner gets a substantial silicone bumper while the other gets a slim, neat lip. It is made from 70 Shore A silicone, firm enough to hold its square shape and flexible enough to follow gentle curves, and it is rated from -50°C to +180°C. It comes as a continuous 25m coil in seven colours, all held in stock for same-day dispatch.
At a glance
- Size: 7.5mm wide x 5.5mm high, solid L section
- Section: 5.0mm upright, 2.0mm base. The inside step is 2.5mm wide x 3.5mm deep.
- Material: silicone rubber, 70 Shore A, rated -50°C to +180°C
- Compliance: FDA 21 CFR 177.2600, EC 1935/2004 and WRAS approved material
- Colours: black, blue, green, red, translucent, white and yellow
- Supplied as: one 25m coil, £675.00 inc VAT (£27.00 per metre)
Technical drawing
![]()
Nominal dimensions in mm. Tolerances are to ISO 3302-1:2014 class E2 for extruded solid rubber sections.
Specification
| Property | Value | Test method |
|---|---|---|
| Profile type | Solid L (angle) section | – |
| Overall width | 7.5 mm | Nominal, ISO 3302-1 E2 |
| Overall height | 5.5 mm | Nominal, ISO 3302-1 E2 |
| Upright (leg) width | 5.0 mm | Nominal, ISO 3302-1 E2 |
| Base thickness | 2.0 mm | Nominal, ISO 3302-1 E2 |
| Wall range | 2 mm to 5 mm | Nominal |
| Inside step (derived) | 2.5 mm wide x 3.5 mm deep | Calculated from the dimensions above |
| Coil length | 25 m continuous | – |
| Material | Silicone rubber | – |
| Hardness | 70 Shore A | DIN ISO 48-4 |
| Density | 1.18 g/cm³ | DIN EN ISO 1183-1 method A |
| Tensile strength | 11.3 N/mm² (11.3 MPa) | ISO 37 type 1 |
| Elongation at break | 530 % | ISO 37 type 1 |
| Tear strength | 31 N/mm | ASTM D624 die B |
| Compression set, 22 h at 175°C | 40 % | DIN ISO 815-1 type B, method A |
| Rebound resilience | 55 % | ISO 4662 |
| Operating temperature | -50°C to +180°C | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, cosmic and ionising radiation, corona discharge | – |
| Dimensional tolerance | ISO 3302-1 class E2 | ISO 3302-1:2014 |
| Colours | Black, blue, green, red, translucent, white, yellow | – |
| SKU | IP-SILP-7.5X5.5-[COLOUR] | – |
All values are for this profile's silicone compound.
Download the technical data sheet (PDF)
Materials and compliance
- FDA 21 CFR 177.2600: the compound complies with the US rule for rubber articles in repeated food contact.
- EC 1935/2004: the compound complies with the EU framework regulation for food-contact materials.
- WRAS approved material: suitable for potable water and public water supply applications.
- Free from TSE/BSE-derived products and free from phthalates.
Food-contact and water approvals cover the material. Check that your finished assembly meets your own process requirements.
Typical uses
- Heavy-duty corner bumper on machine guards, enclosures and HVAC casings, with the thick 5mm upright on the face that takes the knocks
- Impact and abrasion protection for glass, sheet metal and panel edges
- Corner and gap seals on doors, hatches, windows and frames, keeping out water, air and dust
- Food and beverage processing equipment
- Potable water and public water supply equipment
- Cleanrooms and laboratories, where a smooth, wipe-clean edge is needed
- Classic cars, caravans, motorhomes and rail vehicles
- Colour coding: use red, blue, green or yellow to mark hygiene zones or hazard edges
How it fits
The inside step of the L sits over a 90° outside corner. It covers 2.5mm of one face, under the 2mm base lip, and 3.5mm of the other face, under the 5mm-thick upright. Put the upright on the face most likely to be struck.
- Clean and degrease the edge first.
- For many edge-protection jobs it can simply be laid in place without adhesive. For a permanent or watertight joint, bed it in a compatible silicone or polyurethane adhesive sealant.
- Lay it in relaxed, without stretching. Cut slightly long, then trim.
- Cut with a sharp knife or shears. Mitre at 45° for neat closed corners.
Which one do I need?
| Need | Suggested profile |
|---|---|
| Thick 5mm bumper on one face, slim 2mm lip on the other | This 7.5mm x 5.5mm silicone L profile, 70 Shore A |
| Smaller corner cap with even 3mm walls | Silicone L profile 6.2mm x 5.2mm |
| Hard, taller small angle | Silicone L profile 5mm x 6mm, 80 Shore A |
| Slightly taller leg to cover a deeper edge | Silicone L profile 7.7mm x 7.1mm |
| Wider face covering a broader flat surface | Silicone L profile 10mm x 5mm |
| Larger section | Silicone L profile 12.5mm x 7.5mm |
How much do I need?
Measure every edge you want to cover and add about 5% for cuts and mitres. For example, ten guard panels, each with two 600mm edges to protect, need 10 x 2 x 0.6m = 12m, plus 5% = about 12.6m. One 25m coil covers that job twice. At £27.00 per metre, a full coil is the most economical way to buy.
Frequently asked questions
How does it fit onto an edge?
Seat the inside step of the L over an outside corner. It wraps 2.5mm onto one face and 3.5mm onto the other. For light-duty edge protection it can be laid in place without adhesive; for a permanent or watertight fit, bond it with silicone or polyurethane sealant.
What size edge or corner does it suit?
It suits any 90° outside corner. The step covers 2.5mm x 3.5mm, and overall the profile adds 7.5mm x 5.5mm to the corner: 5mm of silicone on the upright face and 2mm on the base face.
Is it food safe?
Yes. The compound meets FDA 21 CFR 177.2600 and EC 1935/2004 for food-contact use, and it is free from phthalates and TSE/BSE-derived products.
Can it be used near drinking water?
Yes. The material is WRAS approved for potable water applications.
What temperatures can it take?
It works continuously from -50°C to +180°C. It also resists UV, ozone and weathering, so it is suitable outdoors.
How hard is it, and will it spring back?
It is 70 Shore A: firm enough to stay square on a corner, but still flexible. Its compression set is 40% after 22 hours at 175°C, so it recovers well when pressed, which helps it keep sealing over time.
How do I cut and join it?
Cut it with a sharp knife or shears on a cutting board. Mitre corners at 45° and bond the joint with a silicone adhesive sealant. Do not join it with standard cyanoacrylate glues: silicone does not bond well without a silicone primer.
Is it in stock, and how is it supplied?
Yes. All seven colours are held in stock as continuous 25m coils, priced per coil.
Need help choosing a silicone L profile? Contact our team on +44 1282 277786 or sales@industrial-polymers.co.uk.
Product details
| SKU | IP-SILP-7.5X5.5-BLACK |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone L Profile – 7.5mm x 5.5mm – 25m Coil