Rubber & FoamSKU IP-SILP-10X7-BLACK
Silicone L Profile – 10mm x 7mm – 25m Coil
Silicone L profile 10mm x 7mm is a flexible right-angle angle trim with a 10mm base leg and a chunky 7mm upright, used to protect and seal sheet edges, panel corners and enclosure doors. It is sold per 25m coil in a choice of seven colours.
At a glance
- Unequal L section: 10mm base leg (2mm wall) and 7mm upright leg (3.5mm wall)
- 60 Shore A silicone rubber angle trim that stays flexible from -50°C to +180°C
- Material stated as FDA compliant for food contact and WRAS approved for drinking water
- Resists UV, ozone and weathering, so it suits indoor and outdoor edges
- Seven colours: black, blue, green, red, translucent, white and yellow
- Supplied as one continuous 25m coil, cut to length on site
Typical uses
- Rubber edge protector for sheet metal, glass and acrylic panel edges
- Silicone corner seal on machine guard doors and enclosure lids
- Food and drink processing equipment where a colour-coded trim helps hygiene zoning
- Finishing exposed corners in cleanrooms, laboratories and test rigs
Which one do I need?
| Profile | Best suited to |
|---|---|
| 7.7mm x 7.1mm | Near-equal legs for a neat, symmetrical corner on small parts |
| 10mm x 5mm | Same 10mm base with a lower upright where clearance is tight |
| 10mm x 7mm (this profile) | 10mm base with a thicker 7mm upright that takes knocks on the exposed corner |
| 10mm x 10mm heavy wall | Equal 10mm legs with a heavy wall for harder-wearing corners |
| 12.5mm x 7.5mm | A wider base for more bonding area on flat faces |
Technical drawing
Specification
| Profile | L section (angle), unequal legs |
| Base leg | 10mm wide, 2mm wall |
| Upright leg | 7mm high, 3.5mm wall |
| Material | Silicone rubber |
| Hardness | 60 Shore A |
| Tensile strength | 11 N/mm² |
| Elongation at break | 550% |
| Tear strength | 26 N/mm |
| Compression set | 31% (22 hours at 175°C) |
| Operating temperature | -50°C to +180°C |
| Compliance | FDA compliant material, WRAS approved |
| Colours | Black, blue, green, red, translucent, white, yellow |
| Unit of sale | 25m coil |
How much do I need?
Measure every edge to be covered and add about 5% for trimming and mitred corners. For example, edging all four sides of three 600mm x 400mm guard panels needs 3 x 2.0m = 6.0m, plus 5% = 6.3m, so one 25m coil does the job with plenty to spare.
Fitting tips
- Clean the edge with isopropyl alcohol so it is dry and free of oil before fitting.
- Fit the 10mm leg to the flat face and the 7mm leg over the exposed edge, where the thicker wall gives the most protection.
- Cut with a sharp knife against a straight edge for a square end; mitre the corners at 45° for a tidy finish.
- For a permanent or watertight joint, bond with a silicone adhesive sealant, as general-purpose glues do not grip silicone well.
Complete your project
- Silicone L Profile – 10mm x 5mm – 25m Coil
- Silicone L Profile – 10mm x 10mm, Heavy 5mm Wall – 25m Coil
- Silicone L Profile – 12.5mm x 7.5mm – 25m Coil
Questions
What thickness of panel will this angle trim cover?
It is an L section, not a channel, so it sits on the corner rather than gripping the panel. It suits any panel thickness where you want a 10mm face and a 7mm edge cover.
Can I use this silicone corner seal near ovens or heaters?
Yes. The silicone is rated from -50°C to +180°C, so it stays flexible beside warm machinery and in cold rooms.
Is the material suitable for food areas?
The silicone is stated as FDA compliant for food contact, and the coloured versions help with colour-coded hygiene zones.
How do I fix the L profile in place?
Use a silicone adhesive sealant along the inside of both legs. For light-duty dust edges, double-sided tape made for silicone can also work.
Need help choosing a size or colour? Contact our technical team and we will be glad to advise.
Product details
| SKU | IP-SILP-10X7-BLACK |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone L Profile – 10mm x 7mm – 25m Coil