Rubber & FoamSKU IP-SIL-10X9.5-BLACK
Silicone L Profile – 10mm x 9.5mm, 8mm Upright, 4.5mm Base – 60 Shore A – 25m Coil
A heavy, almost solid silicone L profile: 10mm wide and 9.5mm tall, with an 8mm upright and a 4.5mm base that leave a small 2mm x 5mm rebate along one edge. It gives a tough, cushioned stop or edge strip that will not crush flat, and the 60 Shore A silicone stays flexible from -50°C to +180°C. Sold as a 25m continuous coil in seven colours, held in UK stock.
At a glance
- Size: 10mm wide x 9.5mm high, solid section (not a thin-walled angle)
- Legs: 8mm upright and 4.5mm base, forming a 2mm wide x 5mm deep rebate
- Material: 60 Shore A silicone rubber, 1.15 g/cm³
- Temperature: -50°C to +180°C working range
- Compliance stated by the manufacturer: FDA 21 CFR 177.2600, EC 1935/2004, WRAS approved, free from TSE/BSE-derived products and phthalates
- Colours: black, blue, green, red, translucent, white, yellow (one price for every colour)
- Supplied as: 25m coil, cut it to length yourself
Technical drawing
![]()
Orange dimensions are the manufacturer's. The 2mm step width (10 − 8) and 5mm step depth (9.5 − 4.5) are worked out from them. Corners are square.
Specification
| Property | Value | Test method / note |
|---|---|---|
| Profile | L section (stepped angle), solid | Manufacturer's drawing |
| Overall width | 10 mm | Nominal |
| Overall height | 9.5 mm | Nominal |
| Upright (top leg) width | 8 mm | Nominal |
| Base thickness | 4.5 mm | Nominal |
| Rebate (step) size | 2 mm wide x 5 mm deep | Derived from the dimensions above |
| Section thickness range | 4.5 mm to 8 mm | Manufacturer's data |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Coil length | 25 m continuous | One coil per unit |
| Material | Silicone rubber | - |
| Hardness | 60 Shore A | DIN ISO 48-4 |
| Density | 1.15 g/cm³ | DIN EN ISO 1183-1 A |
| Tensile strength | 11 N/mm² (11 MPa) | ISO 37 Type 1 |
| Elongation at break | 550 % | ISO 37 Type 1 |
| Tear strength | 26 N/mm (26 kN/m) | ASTM D624 B |
| Compression set | 31 % after 22 h at 175°C | DIN ISO 815-1 Type B, Method A |
| Rebound resilience | 59 % | ISO 4662 |
| Working temperature | -50°C to +180°C | Manufacturer's data |
| Environmental resistance | Ozone, UV, oxidation, weathering, corona discharge, cosmic and ionising radiation | Manufacturer's data |
| Colours | Black, blue, green, red, translucent, white, yellow | - |
Materials and compliance
The manufacturer's datasheet for this exact profile states that the compound meets:
- FDA 21 CFR 177.2600 (rubber articles for repeated food contact)
- EC 1935/2004 (EU food-contact materials framework)
- WRAS approved material (for use with drinking water)
- Free from TSE/BSE-derived products
- Free from phthalates
We list only approvals the manufacturer states in writing for this product. If you need a declaration of conformity or a certificate for an audit, ask us before ordering.
How it fits
![]()
The wide 10mm base face bonds flat to a frame, worktop or machine panel. The 8mm upright gives a solid stop or bumper face. The 2 x 5mm rebate can locate the edge of a thin sheet, or simply leave a stepped edge.
Typical uses
- Rebated edge stops and bumpers on food and drink processing equipment
- Seals and stops on doors, hatches, guards and HVAC enclosures
- Edging in potable water equipment (WRAS approved material)
- Hot-zone edging near ovens, dryers and heat-sealing machines, up to +180°C
- Colour-coded edging for food zones, cleanrooms and laboratories
- Edge protection on caravans, vehicles and outdoor kit, where UV and ozone resistance matter
Which profile do I need?
| Profile | Best for |
|---|---|
| 10mm x 9.5mm (this one) | Near-solid block with a small 2 x 5mm rebate. Hard-wearing stop or bumper |
| 10mm x 7.9mm | A lower section on the same width |
| 9mm x 11mm | A true angle with thinner legs, to wrap over a corner |
| 11mm x 10mm | Slightly larger, also sold in 10m coils |
| 12.5mm x 9.4mm | A wider base on a similar height |
Fitting and care
- Clean and degrease the mounting face. Silicone sealant bonds best to dry, oil-free metal, glass or plastic.
- Bond the 10mm base face with a continuous bead of silicone or a compatible polyurethane sealant/adhesive. Where the part only needs locating, it can be pushed into place without adhesive.
- Cut with a sharp knife or shears against a straight edge for a square end. Cut a few millimetres long and butt the ends together so there is no gap.
- Clean with warm soapy water or your normal food-area cleaning routine. No other maintenance is needed.
Questions
Is this a thin angle that wraps over a corner?
No. It is a heavy, almost solid section: an 8mm upright on a 4.5mm base with a small 2mm x 5mm rebate. If you need an angle that sits over a panel corner, look at the 9mm x 11mm or 11mm x 10mm profiles in the table above.
What size panel or sheet fits the rebate?
The rebate is 2mm wide and 5mm deep, so it can take the edge of a sheet up to about 2mm thick. Check your sheet against the drawing. If your panel is thicker, a U channel will hold it better.
Can it be used in food areas?
Yes. The manufacturer states that the compound meets FDA 21 CFR 177.2600 and EC 1935/2004 for food contact. Bright colours such as blue are often chosen for food zones because they are easy to spot.
Is it suitable for drinking water equipment?
Yes. The material is WRAS approved.
How hot and cold can it go?
The working range is -50°C to +180°C. The compression set figure (31% after 22 hours at 175°C) is measured at the top of that range, so the data reflects hot service.
Will it survive outdoors?
Yes. Silicone resists UV, ozone and weathering, so it will not crack or perish in sunlight the way many black rubbers can.
How do I cut and join it?
Cut it with a sharp knife or shears. To join it, butt the square-cut ends together and seal them with a dab of silicone sealant. Mitre the ends at 45° for neat corners.
How much do I get, and is it in stock?
Each unit is a full 25m coil, which works out at £27.00 per metre. All seven colours are held in stock and dispatched from the UK.
Need help choosing a profile or a quote for several coils? Contact our team or call +44 1282 277786.
Product details
| SKU | IP-SIL-10X9.5-BLACK |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone L Profile – 10mm x 9.5mm, 8mm Upright, 4.5mm Base – 60 Shore A – 25m Coil