Rubber & FoamSKU IP-SILP-9X11-BLACK
Silicone L Profile – 9mm x 11mm – 25m Coil
A solid silicone angle (L) profile, 9mm wide by 11mm high, with a 3mm upright wall and a thicker 4mm base wall. Push it over a sheet edge or outside corner to protect it, cushion it or seal it. The silicone is firm (70 Shore A), works from -50°C to +180°C, and is made from a compound with food-contact (FDA and EC 1935/2004) and WRAS approvals. Sold as a continuous 25m coil in seven colours, from stock with same-day dispatch.
At a glance
- Size: 9mm wide x 11mm high, 3mm upright wall, 4mm base wall
- Inside of the angle: 6mm along the base and 7mm up the upright
- Material: solid silicone rubber, 70 Shore A
- Temperature: -50°C to +180°C continuous working range
- Approvals: FDA 21 CFR 177.2600, EC 1935/2004, WRAS approved material
- Weathering: resists UV, ozone, oxidation and outdoor exposure
- Colours: black, blue, green, red, translucent, white, yellow
- Supplied as: one 25m coil (£27.00 per metre inc VAT)
Technical drawing
![]()
Specification
| Property | Value | Test method / note |
|---|---|---|
| Profile type | Solid L / angle section | - |
| Overall width (base) | 9.0 mm | Nominal |
| Overall height (upright) | 11.0 mm | Nominal |
| Upright wall thickness | 3.0 mm | Nominal |
| Base wall thickness | 4.0 mm | Nominal |
| Inner leg, base (9 - 3) | 6.0 mm | Derived from the nominal sizes |
| Inner leg, upright (11 - 4) | 7.0 mm | Derived from the nominal sizes |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Coil length | 25 m continuous | - |
| Material | Silicone rubber | - |
| Hardness | 70 Shore A | DIN ISO 48-4 |
| Density | 1.18 g/cm³ | DIN EN ISO 1183-1 A |
| Tensile strength | 11.3 N/mm² (MPa) | ISO 37 Type 1 |
| Elongation at break | 530 % | ISO 37 Type 1 |
| Tear strength | 31 N/mm | ASTM D 624 B |
| Compression set, 22 h at 175°C | 40 % | DIN ISO 815-1 Type B, Method A |
| Rebound resilience | 55 % | ISO 4662 |
| Working temperature | -50°C to +180°C | - |
| Environmental resistance | Ozone, UV, oxidation, weathering, cosmic and ionising radiation, corona discharge | Supplier material data |
| Colours | Black, blue, green, red, translucent, white, yellow | - |
Materials and compliance
The manufacturer's data for this profile states the following in writing:
- FDA 21 CFR 177.2600 compliant compound (rubber articles for repeated food contact)
- EC 1935/2004 compliant for food-contact materials
- WRAS approved material, for use with potable (drinking) water
- Free from TSE/BSE-derived by-products
- Free from phthalates
Food-contact and WRAS approvals apply to the material. Check the finished installation against the rules for your own application.
Typical uses
- Edge protector on sheet-metal guards, panels, cabinets and enclosure corners
- Corner seal on doors, hatches, access panels and machinery housings
- Hygienic edge trim on stainless food and drink equipment (FDA / EC 1935/2004 material)
- Potable-water equipment and tanks where a WRAS approved material is specified
- Glass and panel edges in cleanrooms, laboratories and HVAC housings
- Colour-coded edges for zoning, identification or safety marking
- Caravan, motorhome, classic car and rail trim
Which size do I need?
Measure the corner you want to cover. The inside of this angle is 6mm across the base and 7mm up the upright, so it suits panel edges and corners where those faces have room for it. The 4mm base wall is the thicker, more protective face.
| Profile | Best for |
|---|---|
| 7.7mm x 7.1mm | Smaller angle for lighter edges |
| 9mm x 11mm (this one) | Firm 70 Shore A angle with 3mm and 4mm walls |
| 10mm x 9.5mm | Similar size, wider base |
| 10mm x 12mm | Slightly larger angle |
| 10.5mm x 13mm | Heavy-duty corner cushion |
How much do I need?
Add up every edge you want to cover and allow about 5% for trimming. Trimming both front edges and the top of an 800mm wide, 1800mm tall enclosure door needs 1.8 + 1.8 + 0.8 = 4.4m, so one 25m coil covers five doors.
Fitting
- Clean and dry the edge. Remove oil, dust and old sealant.
- Cut the profile to length with a sharp knife or shears. Cut square for butt joints, or mitre at 45° for neat corners.
- Press it on so the inside corner of the L sits right into the corner of the edge, then work along the full length.
- For a permanent or watertight fit, bond it with a compatible silicone or polyurethane adhesive/sealant.
Frequently asked questions
How do I fit it?
Press it over the edge so both faces of the corner sit inside the L. On many edges it stays put as a push-on fit. Where it must not move, or must keep water out, bond it with a compatible silicone or polyurethane sealant.
What size of corner does it fit?
The inside of the angle measures 6mm across the base and 7mm up the upright. The outside is 9mm x 11mm. Compare those numbers with the faces you want to cover; the technical drawing above shows every dimension.
What is it used for?
Protecting and finishing sharp sheet edges and outside corners, sealing door and panel corners, and colour-coded or hygienic trim on food, water, laboratory and HVAC equipment.
Is it safe for food and drinking water?
The silicone compound is stated to comply with FDA 21 CFR 177.2600 and EC 1935/2004 for food contact, and it is a WRAS approved material for potable water. It is also free from phthalates and TSE/BSE-derived ingredients.
What temperatures can it take?
-50°C to +180°C. It stays flexible in freezers and cold stores and keeps its shape near ovens and hot equipment. It also resists UV, ozone and weathering, so it can be used outdoors.
How hard or flexible is it?
70 Shore A, a firm grade of silicone. It holds its shape on an edge and resists knocks, but still bends easily around large curves.
Can I cut and join it?
Yes. Cut it with a sharp knife or shears. For corners, mitre two ends at 45°. Joints can be sealed or bonded with a silicone adhesive/sealant; ordinary superglue does not bond well to silicone.
Does the colour change the specification?
No. All seven colours are the same 9mm x 11mm profile in the same 70 Shore A silicone with the same data. Choose the colour for looks, identification or zoning.
Is it in stock?
Yes. All colours are held in stock as 25m coils and dispatched the same day on qualifying orders.
Need help choosing a profile or colour? Contact our team, call +44 1282 277786 or email sales@industrial-polymers.co.uk.
Product details
| SKU | IP-SILP-9X11-BLACK |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone L Profile – 9mm x 11mm – 25m Coil