Rubber & FoamSKU IP-SIRU-5X14-25-BLACK
Silicone Round U Channel – 5mm x 14mm for 2mm Edges – 25m Coil
A deep-slot silicone U channel with a fully rounded back, 5mm across and 14mm tall, for edges about 2mm thick: 14-gauge sheet steel, aluminium sheet, 2mm acrylic and polycarbonate, thin glass and laminate. The 2mm slot runs 12.5mm deep, nearly twice the depth of the 5mm x 8mm version, so it wraps a long way down both faces of the edge, grips harder and stays put on vibrating or frequently handled panels. Its 1.5mm walls and 1.5mm solid, half-round crown give a soft, smooth bumper with no square corners to catch on. The compound is approved for food contact and drinking water (see Material compliance). Supplied as one continuous 25m coil in seven colours, all held in stock.
At a glance
- Fits edges about 2mm thick (roughly 1.8 to 2.3mm)
- 5mm wide x 14mm high, 2mm slot, 12.5mm slot depth, 1.5mm walls, 1.5mm solid full-round base (R2.5)
- Deep 12.5mm grip: covers more of the edge face and resists pulling off
- Silicone rubber, 60 Shore A: flexible, and follows curves and corners
- Continuous service from -50°C to +180°C
- FDA 21 CFR 177.2600, EC 1935/2004 and WRAS approved compound
- Unaffected by UV, ozone and weather, so it will not crack or harden outdoors
- Black, blue, green, red, translucent, white or yellow, all at the same price
- 25m coil, £27.00 per metre inc VAT
Technical drawing
![]()
Typical uses
- Capping the edges of 2mm stainless and aluminium guards, hoppers, chutes and splash screens on food and packaging lines, where a deep grip stops the trim working loose under vibration
- Finishing 2mm acrylic and polycarbonate sneeze screens, display panels and machine windows with a trim that hides more of the cut edge
- Cushioning glass or polycarbonate in cabinet doors, inspection hatches and display cases
- Edge trim on tank lids, access hatches and covers in contact with drinking water
- Edge protection on oven, heater, dryer and lighting panels where rubber or PVC trims would degrade
- Colour-coding guards, trays and fixtures by line, zone or allergen
Which size do I need?
Measure the edge thickness and choose the slot that matches it most closely. For the same slot, a deeper channel covers more of the edge face and grips harder.
| Silicone U channel | Slot / edge thickness |
|---|---|
| Silicone Round U Channel 3mm x 5mm | 1mm |
| Silicone Round U Channel 4mm x 9.5mm | 1mm, 7.5mm deep |
| Silicone Round U Channel 3.2mm x 7.8mm | 1.2mm, 5mm deep |
| Silicone Round U Channel 4.1mm x 9mm | 1.5mm, 7.5mm deep |
| Silicone Round U Channel 4.7mm x 15mm | 1.5mm, 13.5mm deep |
| Silicone Round U Channel 5mm x 8mm | 2mm, 6.5mm deep, round back |
| Silicone Round U Channel 5mm x 14mm (this one) | 2mm, 12.5mm deep, round back |
| Silicone Round U Channel 5mm x 4mm | 3mm, 3mm deep |
| Silicone U Channel 7.1mm x 13mm | 4mm |
| Silicone U Channel 15mm x 20mm | 10mm |
Specification
| Property | Value | Test method |
|---|---|---|
| Profile and dimensions | ||
| Profile | Round-bottom U channel (push-on edge trim) | – |
| Overall width | 5.0 mm | – |
| Overall height | 14.0 mm | – |
| Slot (grip) width | 2.0 mm | – |
| Slot depth | 12.5 mm | – |
| Wall thickness | 1.5 mm each side | – |
| Base | 1.5 mm solid, full-round bottom (R2.5) | – |
| Fits panel / edge | 2 mm nominal | – |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Weight (calculated) | approx. 49 g per metre, approx. 1.2 kg per 25 m coil | From cross-section and density |
| Material properties (typical) | ||
| Material | Silicone rubber (VMQ) | – |
| Hardness | 60 Shore A | DIN ISO 48-4 |
| Density | 1.15 g/cm³ | DIN EN ISO 1183-1 A |
| Tensile strength | 11 N/mm² (11 MPa) | ISO 37 Type 1 |
| Elongation at break | 550 % | ISO 37 Type 1 |
| Tear strength | 26 N/mm (26 kN/m) | ASTM D624 B |
| Compression set | 31 % after 22 h at 175 °C | DIN ISO 815-1 Type B, Method A |
| Rebound resilience | 59 % | ISO 4662 |
| Operating temperature | -50 °C to +180 °C continuous | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, cosmic and ionising radiation, corona discharge | – |
| Supply | ||
| Colours | Black, blue, green, red, translucent, white, yellow | – |
| Unit of sale | One continuous 25 m coil | – |
Material compliance
The manufacturer's datasheet for this exact profile states that its silicone compound meets:
- FDA 21 CFR 177.2600: the US regulation for rubber articles in repeated contact with food
- EC 1935/2004: the EU and UK framework regulation for food-contact materials
- WRAS approved: approved for contact with drinking (potable) water in the UK
- Free from TSE/BSE by-products: no animal-derived ingredients of TSE/BSE concern
- Phthalate-free: contains no phthalate plasticisers
These approvals apply to the material. Whether a finished assembly complies depends on its design and use. Compliance documents are available on request: contact our team.
How much do I need?
Add up every edge you want to cover and allow about 5% for trimming and joints. Example: six 2mm stainless machine guards, each 1000mm wide x 700mm high with trim along the top and both sides (2.4m each), need 14.4m, or about 15.1m with allowance. One 25m coil covers the job with spare.
Fitting tips
- Deburr the edge and wipe off oil and dust before fitting
- Start at one end and press the channel on with your thumb, working along the edge until it is fully seated; with a 12.5mm slot this takes a firm, steady push
- A little soapy water on the edge helps it slide on; let it dry before use
- Cut slightly over length with a sharp knife and push the ends together for a tight butt joint
- On edges under 1.8mm, or where it must be sealed or permanent, run a bead of silicone or polyurethane sealant into the slot first
Questions
What edge thickness will it fit?
The slot is 2mm. Silicone stretches a little, so edges from about 1.8mm to 2.3mm usually hold well. On thinner edges add a little silicone sealant so it cannot slide off; for 1.5mm edges the 4.7mm x 15mm channel is the closest deep-slot fit, and for 3mm edges the 5mm x 4mm channel.
Should I choose this or the 5mm x 8mm channel?
Both take a 2mm edge with the same rounded back. This 14mm version grips 12.5mm down each face instead of 6.5mm, so it holds harder, hides more of a rough or cut edge and suits panels that vibrate or are handled often. Choose the 5mm x 8mm where a slimmer, lower-profile trim is wanted.
Is it suitable for food equipment?
Yes. The compound is stated to meet FDA 21 CFR 177.2600 and EC 1935/2004, so it suits guards, covers and panels on food processing, packaging and catering equipment.
Can it be used with drinking water?
Yes. The material is WRAS approved for contact with potable water.
Is it suitable for hot equipment or outdoor use?
Yes. It is rated for continuous use from -50°C to +180°C and resists UV, ozone and weathering.
How do I cut and join it?
Cut it square with a sharp craft knife or scissors. For a neat joint, butt the two ends together; for a sealed joint, bond them with a silicone adhesive.
Will it go round corners?
Yes, it follows curves and rounded corners well. Because the legs are 14mm tall, sharp bends need a larger radius than shallow trims; on a sharp 90° corner, cut a small V notch out of the walls or butt two lengths together.
How accurate are the dimensions?
It is extruded to ISO 3302-1 tolerance class E2, the standard precision class for rubber extrusions, so allow a few tenths of a millimetre either way on the nominal sizes.
Is it in stock?
Yes. All seven colours are held in stock, so orders go out quickly, as shown by the dispatch message above.
Can I order a shorter length or a bulk quantity?
This listing is a full 25m coil. For cut lengths or multiple coils, ask our team for a quote.
Are all colours the same price?
Yes. Every colour is the same profile, the same compound and the same price.
Need help choosing an edge trim or seal? Call +44 1282 277786, email sales@industrial-polymers.co.uk or contact our team.
Product details
| SKU | IP-SIRU-5X14-25-BLACK |
|---|---|
| Weight | 2.65 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone Round U Channel – 5mm x 14mm for 2mm Edges – 25m Coil