Rubber & FoamSKU IP-SITS-3.7X8.2-25M-BLK
Silicone T Seal Profile – 3.7mm x 8.2mm – 25m Coil
A firm, solid silicone T seal for slots about 2.4mm wide. The 2.4mm leg pushes into the slot and holds the seal in place; the 3.7mm head sits on the surface and closes the joint against dust, splash, draughts and heat. At 80 Shore A it is noticeably stiffer than most silicone seals, so the head stays crisp and square and resists being dragged out of the slot. It comes as one unbroken 25m coil in seven colours.
At a glance
- Head: 3.7mm wide × 2.4mm deep, flat face
- Leg: 2.4mm wide × 5.8mm long, 8.2mm overall height
- Solid silicone rubber, 80 Shore A (firm), working range -50°C to +180°C
- Compound stated to meet FDA 21 CFR 177.2600 and EC 1935/2004 for food contact; WRAS approved material
- Black, white, translucent, red, green, blue or yellow: same size and same price
- Held in stock in all seven colours
- £675.00 per 25m coil inc VAT, which works out at £27.00 per metre
Typical uses
- Inspection hatches and access panels on food and packaging machinery
- Door and lid seals on catering hot cupboards, warming cabinets and proving units
- Slot seals in aluminium extrusion frames, machine guards and enclosures
- HVAC access doors, duct panels and heater housings
- Colour-coded seals for hygiene zones (red, green, blue, yellow)
Technical drawing
![]()
Full specification
| Property | Value | Test method |
|---|---|---|
| Dimensions | ||
| Profile type | Solid T section, square-edged head | – |
| Overall height | 8.2 mm | – |
| Head width | 3.7 mm | – |
| Head depth | 2.4 mm | – |
| Leg width | 2.4 mm | – |
| Leg length below head | 5.8 mm (8.2 minus 2.4) | – |
| Shoulder each side of leg | 0.65 mm | – |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Length per coil | 25 m, one continuous length | – |
| Material and physical properties | ||
| Compound | Solid silicone rubber | – |
| Hardness | 80 Shore A | DIN ISO 48-4 |
| Density | 1.20 g/cm³ | DIN EN ISO 1183-1, method A |
| Tensile strength | 10 N/mm² (10 MPa) | ISO 37, type 1 |
| Elongation at break | 440 % | ISO 37, type 1 |
| Tear strength | 28 N/mm (28 kN/m) | ASTM D624, die B |
| Compression set | 78 % after 22 h at 175 °C | DIN ISO 815-1, type B, method A |
| Rebound resilience | 54 % | ISO 4662 |
| Approximate weight | About 27 g per metre (calculated from section area and density) | – |
| Service conditions | ||
| Working temperature | -50 °C to +180 °C | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, corona discharge, cosmic and ionising radiation | – |
| Supply | ||
| Colours | Black, white, translucent, red, green, blue, yellow | – |
| Unit of sale | 1 coil of 25 m (£27.00 per metre inc VAT) | – |
Materials and compliance
These are the claims the manufacturer makes in writing for this exact profile and compound. Ask us for the certificate or declaration your file needs.
| Claim | What it means for you |
|---|---|
| FDA 21 CFR 177.2600 | The compound meets the US rule for rubber articles in repeated contact with food. |
| EC 1935/2004 | The compound meets the EU framework regulation for materials that come into contact with food. |
| WRAS approved material | The material is accepted for contact with drinking water in UK water fittings. |
| Free from TSE/BSE by-products | No animal-derived ingredients that carry TSE/BSE risk. |
| Phthalate free | Made without phthalate plasticisers. |
Approvals cover the material as supplied. Whether your finished assembly complies also depends on its design, cleaning regime and the other materials in it, so check against your own requirements.
Will it fit my slot?
Measure the slot width and depth. The leg is 2.4mm wide, so it grips best in a slot of about 2.2–2.4mm. Because this compound is firm, it will not squeeze into a slot much narrower than that. The slot needs to be at least 5.8mm deep so the head can sit down flat on the surface. In a slot that is slightly wide, run a thin bead of silicone adhesive along the bottom first so the leg cannot work loose.
How much do I need?
Add up the length of every slot and allow about 5% for trimming and joints. Example: a machine hatch with a 500mm × 400mm seal track needs 1.8m, or about 1.9m with allowance, so one 25m coil seals 13 hatches.
Fitting tips
- Clear old seal, grease and grit out of the slot and let it dry
- Start partway along a straight side, not at a corner
- Press the leg in with your thumb or a small plastic roller as you go; a firm seal needs steady, even pressure
- At corners, cut a small V-notch out of the leg so the head turns cleanly without bunching
- Lay the seal in rather than stretching it: stretched silicone shrinks back and opens a gap
- Cut slightly long with a sharp knife and push the ends together; a dab of silicone adhesive keeps the joint closed
FAQ: frequently asked questions
Which way up does it go?
The 2.4mm leg goes into the slot and the 3.7mm head sits on the surface, covering the slot with about 0.65mm of overlap each side.
How firm is 80 Shore A?
Firm, similar to a hard shoe heel. It holds its shape and resists being pulled out of the slot, but it needs more closing force than a soft seal. If your door or lid closes lightly onto the seal, a softer profile may suit better; ask us.
Will it stay springy over time?
This compound has a compression set of 78% after 22 hours at 175°C, which is high. It works best where the head is a cover or a light-contact seal rather than being squashed hard under heat all the time. For a seal that must keep pushing back under constant hot compression, ask us about a softer, lower-set silicone T seal.
Can it be used near ovens and heaters?
It is rated from -50°C to +180°C. It suits door frames, cabinet lids and warming or proving equipment where the seal stays at or below that temperature. For hotter positions, ask us about a higher-rated profile.
Is it safe near food or drinking water?
The compound is stated to meet FDA 21 CFR 177.2600 and EC 1935/2004 for food contact, and it is a WRAS approved material. We can send the declaration if your audit needs it.
How accurate are the dimensions?
The profile is extruded to ISO 3302-1 class E2, the normal tolerance class for extruded rubber sections. Check your slot against the drawing before ordering.
What glue works with it?
Use a silicone adhesive or silicone sealant. Most general-purpose glues and contact adhesives will not bond to silicone rubber.
Can I buy a shorter length?
This listing is a full 25m coil. For a cut length or a large quantity, contact us for a quote.
Is every colour the same price?
Yes. All seven colours are £675.00 per 25m coil inc VAT, so you can colour-code by area at no extra cost.
Complete your project
- Silicone T Seal Profile – 3mm x 6.5mm (smaller, 2mm leg)
- Silicone T Seal Profile – 4mm x 6.5mm
- Silicone T-Section Seal – 10mm x 10mm
Not sure this profile suits your slot? Send us a photo or the slot size and we will check it for you. Contact our team.
Product details
| SKU | IP-SITS-3.7X8.2-25M-BLK |
|---|---|
| Weight | 1.76 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone T Seal Profile – 3.7mm x 8.2mm – 25m Coil