Rubber & FoamSKU IP-SITS-7X4.5-25M-BLK
Silicone T Seal Profile – 7mm x 4.5mm – 25m Coil
A wide, sturdy push-fit seal for slots too wide for a thin-legged T seal. This silicone T seal profile is a solid 7mm x 4.5mm extrusion with a square-edged flat head (7mm wide, 2mm deep) on a broad 4.2mm leg. Press the leg into a slot about 4mm wide and the head stands 2mm proud, giving the closing door, lid or panel a full 7mm contact band, while the shoulders cover 1.4mm of frame either side. At 60 Shore A it is a medium-soft silicone that seals with modest closing force and recovers well after compression. Supplied as one continuous 25m coil in seven colours.
£675.00 inc VAT per 25m coil, which is £27.00 per metre.
At a glance
- Flat head 7mm wide and 2mm deep, square edges, 1.4mm shoulder each side of the leg
- Wide 4.2mm leg, 2.5mm long: a push fit in a slot about 3.9–4.2mm wide and at least 2.5mm deep
- Overall height only 4.5mm for low-clearance frames; the head stands 2mm proud before compression
- Medium-soft solid silicone, 60 Shore A, with 550% elongation, 59% rebound and 31% compression set (22 h at 175°C)
- Works from -50°C to +180°C without hardening or going brittle
- Food-contact compound (FDA 21 CFR 177.2600 and EC 1935/2004) and WRAS approved material
- 25m coil in black, white, translucent, red, green, blue or yellow, all the same price
Typical uses
- Lids, guards and inspection hatches on food processing, packaging and brewing equipment
- Oven, proving cabinet and drying room doors with a 4mm seal slot
- HVAC access panels, duct inspection doors and heated enclosures
- Replacement seals where an old, wider slot has worn too loose for a thin-legged profile
- Hatch, window and trim seals on marine and vehicle bodywork
- Colour-coded seals for hygiene zones (blue, green, yellow, red)
Technical drawing
![]()
Full specification
| Property | Value | Test method |
|---|---|---|
| Dimensions | ||
| Profile type | Solid T section, flat square-edged head, straight wide leg | – |
| Overall width (head) | 7.0 mm | – |
| Overall height | 4.5 mm | – |
| Head depth | 2.0 mm | – |
| Leg (base) width | 4.2 mm | – |
| Leg length below head | 2.5 mm (reference, 4.5 − 2.0) | – |
| Shoulder overhang each side | 1.4 mm (reference, (7.0 − 4.2) ÷ 2) | – |
| Suggested slot | About 3.9–4.2 mm wide, at least 2.5 mm deep | Guidance |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Length per coil | 25 m, one continuous length | – |
| Material and physical properties | ||
| Material | Solid silicone rubber | – |
| Hardness | 60 Shore A | DIN ISO 48-4 |
| Density | 1.15 g/cm³ | DIN EN ISO 1183-1 A |
| Tensile strength | 11 N/mm² (11 MPa) | ISO 37 Type 1 |
| Elongation at break | 550 % | ISO 37 Type 1 |
| Tear strength | 26 N/mm | ASTM D624 B |
| Compression set | 31 % after 22 h at 175 °C | DIN ISO 815-1 Type B, Method A |
| Rebound resilience | 59 % | ISO 4662 |
| Service conditions | ||
| Working temperature | -50 °C to +180 °C | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, corona discharge, cosmic and ionising radiation | – |
| Supply | ||
| Colours | Black, white, translucent, red, green, blue, yellow (same profile and price) | – |
| Approximate weight | About 0.7 kg of rubber per 25 m coil (calculated from section area and density) | Calculated |
| Unit of sale | 1 coil of 25 m (£27.00 per metre) | – |
Materials and compliance claims
These are the claims the manufacturer states for this exact profile and compound. Ask us for the certificate or declaration you need for your technical file.
| Claim | What it means for you |
|---|---|
| FDA 21 CFR 177.2600 | The compound meets the US rule for rubber articles intended for repeated contact with food. |
| EC 1935/2004 | The compound meets the EU framework regulation for materials intended to come into contact with food. |
| WRAS approved material | The material is listed as suitable for contact with drinking water in UK water fittings. |
| Free from TSE/BSE by-products | No animal-derived ingredients that carry TSE/BSE risk. |
| Phthalate free | Made without phthalate plasticisers. |
Approvals apply to the material as supplied. Whether a finished assembly complies also depends on your design, cleaning regime and other materials, so check against your own requirements.
Will it fit my groove?
This profile is made for a straight-sided slot about 3.9–4.2mm wide and at least 2.5mm deep. The 60 Shore A compound squeezes into a slot slightly narrower than the 4.2mm leg for a firm grip; much below 3.8mm it becomes hard to push home. In a slot the same width as the leg or slightly wider, add a thin bead of silicone adhesive along the bottom. The 7mm head overhangs the slot by 1.4mm on each side, so the frame needs at least that much flat land either side of the slot for the shoulders to sit on.
![]()
How much do I need?
Measure every slot and add about 5% for trimming and joints. Example: a cabinet door with a 600mm x 450mm groove needs 2.1m, so one 25m coil does about 11 doors with allowance.
Fitting tips
- Clean old seal and debris out of the slot and let it dry
- Start in the middle of a long side, not at a corner
- Press the leg in with your thumb or a plastic roller until the shoulders sit flat on the frame
- Do not stretch the seal as you go: stretched silicone shrinks back and opens gaps at the joints
- Cut slightly long with a sharp knife or shears and push the ends together for a tight butt joint; a dab of silicone adhesive keeps it closed
FAQ: frequently asked questions
Which way up does it go?
The 4.2mm leg goes into the slot. The flat 7mm face of the head faces outwards, towards the door, lid or panel that closes onto it.
How big a gap does it close?
The head stands 2mm proud of the frame. As a guide for a 60 Shore A silicone, design for about 20–30% squeeze of the head: a closed gap of roughly 1.4–1.6mm between the frame and the closing face. For a larger or uneven gap, choose a taller profile.
What slot size do I need?
A straight slot about 3.9–4.2mm wide and at least 2.5mm deep, with at least 1.4mm of flat frame either side. Check your slot against the drawing before ordering, or send us the dimensions and we will check it.
How is it different from the 6mm x 4.5mm T seal?
Both are 4.5mm tall with a flat head, but this one has a 7mm head, a much wider 4.2mm leg and a softer 60 Shore A compound (the 6mm x 4.5mm is 80 Shore A with a 2mm leg). Choose this one for wider slots and lower closing force.
Why 60 Shore A?
It is a medium-soft grade: soft enough to seal with modest closing force and to grip in the slot, firm enough to keep its square edges. Its compression set of 31% after 22 hours at 175°C means it recovers well on doors that are opened and closed while hot.
Will it survive heat?
It is rated from -50°C to +180°C, so it suits ovens, warming cabinets, dryers and machinery that runs hot, as well as cold stores.
Is it safe near food or drinking water?
Yes. The compound is stated to meet FDA 21 CFR 177.2600 and EC 1935/2004 for food contact, and it is a WRAS approved material. Ask for the certificate if your audit needs it.
How do I cut and join it?
Cut square with a sharp knife or shears. Butt the ends together and bond with a silicone adhesive. With a 4.2mm leg the profile is stiff in the plane of the head, so mitre and bond tight corners rather than bending it round them.
How tight are the dimensions?
The profile is extruded to ISO 3302-1 class E2, a standard tolerance class for extruded rubber.
Can I order a shorter length or a different colour mix?
This listing is a full 25m coil in one colour. For cut lengths, mixed colours or larger quantities, contact us for a quote.
Complete your project
- Silicone T Seal Profile – 6mm x 4.5mm (same height, 2mm leg, 80 Shore A)
- Silicone T Seal Profile – 7.5mm x 6.5mm (wider head, taller profile)
- Silicone T Seal Profile – 6.4mm x 7mm (deeper leg for deeper slots)
Not sure this profile matches your slot? Send us a photo or the slot dimensions and we will check it. Contact our team.
Product details
| SKU | IP-SITS-7X4.5-25M-BLK |
|---|---|
| Weight | 2.2 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone T Seal Profile – 7mm x 4.5mm – 25m Coil