
Rubber & FoamSKU IP-TPEUC-7X18X3-STD
TPE Square U Channel – 7mm x 18mm for 3mm Panels – 25m Coil
A tall, slim, square-section push-on trim for capping the raw edges of 3mm sheet. The profile is 7mm wide and 18mm high, with a 3mm parallel slot running 16mm deep. Both walls and the base are a full 2mm thick, so the trim stays rigid and takes knocks without crushing, while the deep sides cover 16mm of each face of the panel. That long grip holds a clean 3mm edge firmly, usually with no adhesive. It is extruded from black 60 Shore A thermoplastic elastomer (TPE), supplied as one continuous 25m coil, and held in stock.

At a glance
- Fits sheet and panel edges 3mm thick
- 7mm wide x 18mm high, 3mm slot 16mm deep
- Uniform 2mm walls and base: rigid, impact-absorbing and hard to crush
- 16mm gripping arms hold a deep strip of each face, so glue is rarely needed
- Slim 7mm top keeps the finished edge neat and unobtrusive
- 60 Shore A TPE: resists UV, weathering, chemicals and repeated flexing
- Cuts cleanly with a knife; fully recyclable thermoplastic
- Black, 25m coil, about £20.41 per metre
Typical uses
- Capping sharp edges on 3mm sheet-metal machine guards, covers and enclosure panels
- Edge finish on 3mm glazing, acrylic and polycarbonate screens
- Vending machine, kiosk and display cabinet panels
- Furniture, shelving and stair-edge panels
- Running boards and light vehicle or trailer panels
- Protecting sheet stock edges during handling and transport
Which size do I need?
Measure the edge you want to cover and match it to the slot. For 3mm edges there are several TPE options; pick by how much of the face you want covered:
| U channel | Fits edge thickness | Choose it when |
|---|---|---|
| TPE Square U Channel 7mm x 18mm (this one) | 3mm | You want a deep 16mm grip with a slim 7mm face |
| TPE Square U Channel 7mm x 12mm | 3mm | You want a lower, more compact square trim |
| TPE U Channel 7mm x 15mm | 3mm | A mid-height option suits the job |
| TPE Square U Channel 9mm x 17mm | 3mm | You want thicker walls on a 50m coil |
| TPE U Channel 7mm x 24mm | 3mm | You need the deepest grip available |
| TPE Square U Channel 8mm x 12mm | 4mm | Your sheet is 4mm, not 3mm |
Specification
| Property | Value | Test method / source |
|---|---|---|
| Profile and dimensions | ||
| Profile | Square-section U channel (push-on edge trim) | – |
| Overall width | 7.0 mm | Nominal, ISO 3302-1 class E2 |
| Overall height | 18.0 mm | Nominal, ISO 3302-1 class E2 |
| Slot width | 3.0 mm, parallel sides | Nominal |
| Slot depth (gripping arm length) | 16.0 mm | Nominal |
| Wall thickness | 2.0 mm each side | Nominal |
| Base thickness under slot | 2.0 mm | Nominal |
| Fits edge / panel (clamping range) | 3 mm only | Manufacturer data |
| Dimensional tolerance | Cross-section class E2, length class L2 (quality level 2) | ISO 3302-1 |
| Weight | 79 g per metre, approx. 2.0 kg per 25 m coil | Manufacturer datasheet |
| Material | ||
| Material | Thermoplastic elastomer (TPE) | – |
| Hardness | 60 Shore A | Shore A durometer (ISO 48-4) |
| Working temperature | -25 °C to +70 °C | Manufacturer datasheet (a wider -40 °C to +90 °C is also quoted; we list the more cautious datasheet figure) |
| Environmental resistance | UV, weathering, chemicals, flex fatigue; good tear and abrasion resistance | Manufacturer data |
| Density, tensile strength, elongation, tear, compression set | Not published for this profile; ask us if you need them | – |
| Supply | ||
| Colour | Black | – |
| Unit of sale | One continuous 25 m coil | – |
| Availability | Held in stock | – |
Material and compliance
TPE is a rubber-like material that is processed like a plastic. It gives a consistent, rubbery feel, needs no vulcanising, and can be recycled at end of life.
- Weathering: stable in sunlight and outdoor conditions, and resists ageing
- Chemical resistance: stands up to water, mild cleaning agents and general workshop exposure
- Tolerances: extruded to ISO 3302-1, the standard tolerance scheme for rubber and elastomer extrusions
No food-contact, potable-water (WRAS), REACH/RoHS or fire-rating approval is claimed for this profile. If you need a declaration for your file, contact our team.
How much do I need?
Total the length of every edge you want to cover and add about 5% for trimming. Example: six glazed screens, each 1.5m x 0.5m, have 24m of perimeter, or about 25.2m with allowance, so order two 25m coils. Five of the same screens (20m, 21m with allowance) fit on one coil.
Fitting tips
- Check the panel really is 3mm: thinner sheet will sit loose, thicker sheet will splay the arms
- Deburr the edge and wipe it free of oil and grease before fitting
- Start at one end and press the channel on with your thumb as you work along; a soft mallet helps on long runs
- Cut slightly over length with a sharp knife and push the ends together for a tight joint
- The tall 18mm section is stiff across its height, so ease it round gentle curves only; on a tight corner, mitre it or cut a V-notch in the base
- For a permanent or vibration-proof fit, add a thin bead of sealant or adhesive in the slot
Questions
What edge thickness does it fit?
It is made for 3mm edges only. For 2mm sheet choose the 6mm x 12mm square U channel; for 4mm sheet choose the 8mm x 12mm.
How does it differ from the 7mm x 12mm version?
Both fit 3mm edges with the same 7mm face. This one is 6mm taller, with 16mm arms instead of 10mm, so it covers more of each face and holds more firmly without glue.
Does it need glue?
Not usually. The 16mm sides grip a clean 3mm edge firmly on their own. Add adhesive only where there is heavy traffic, vibration, or you want it permanent.
Can it go round curves and corners?
It follows gentle curves. For a tight 90° corner, mitre the channel or notch the base so it folds neatly.
Is it suitable outdoors, and what temperatures can it take?
Yes. TPE resists UV and weathering. The datasheet working range is -25°C to +70°C, so keep it away from ovens, exhausts and other hot surfaces.
How do I cut and join it?
A sharp knife or snips gives a clean square cut. Butt the ends tightly; for a sealed joint, add a dab of instant adhesive.
What is it made of?
Black thermoplastic elastomer (TPE) at 60 Shore A: firm enough to protect, soft enough to push on by hand, and fully recyclable.
Is it food-safe?
No food-contact approval is claimed for this black TPE trim.
How accurate are the dimensions?
The cross-section is extruded to ISO 3302-1 class E2, so allow a few tenths of a millimetre either way on the nominal sizes.
When will it ship?
This trim is held in stock and ships in line with the dispatch times shown on this page.
Can I buy a shorter length?
This listing is a full 25m coil in black. For cut lengths or larger quantities, ask our team for a quote.
Need help choosing an edge trim? Contact our team on +44 1282 277786 or sales@industrial-polymers.co.uk.
Product details
| SKU | IP-TPEUC-7X18X3-STD |
|---|---|
| Weight | 4.85 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:TPE Square U Channel – 7mm x 18mm for 3mm Panels – 25m Coil