
Rubber & FoamSKU IP-TPEU-7X24X3-STD
TPE U Channel – 7mm x 24mm for 3mm Panels – 50m Coil
A deep-grip black TPE U channel made for one job: capping and protecting the edge of 3mm panels. Think 3mm sheet steel and aluminium, machine guards, glazing, acrylic and polycarbonate, step and running-board plates, furniture and kiosk panels. It is 7mm across and 24mm tall. Its two parallel 22mm gripping arms, each 2mm thick, hold the edge down their full depth, so it normally stays put without adhesive and can be pulled off and refitted. Made from 60 Shore A thermoplastic elastomer and supplied as one continuous 50m coil (about 4.95kg).

At a glance
- Fits panel and sheet edges 3mm thick (3mm slot, 3mm clamping range)
- 7mm wide x 24mm high, with 22mm deep gripping arms and 2mm walls
- Long arms contact far more of the panel than a standard U channel, so adhesive is usually not needed
- Push-on and removable: refit it as often as you need
- Thermoplastic elastomer (TPE), 60 Shore A, 99 g per metre
- Good resistance to weathering, UV, chemicals, flex fatigue, tearing and abrasion
- Cuts cleanly with a sharp knife; 100% recyclable thermoplastic
- 50m coil in black, about £12.66 per metre
Typical uses
- Capping the cut edges of 3mm steel or aluminium machine guards, covers and enclosure panels
- Protecting people from sharp sheet edges, and protecting the sheets themselves in storage and transport
- Edging 3mm glazing, acrylic and polycarbonate in screens, cabinets and displays
- Edge trim for running boards, stair and step plates
- Bumper edging on furniture, shop-fitting, vending machine and kiosk panels
Which size do I need?
Measure the edge with a caliper. This channel is made for 3mm only: a thinner edge will be loose and a thicker one will force the arms apart.
| U channel | Fits edge thickness | Grip depth | Coil |
|---|---|---|---|
| TPE U Channel 4mm x 23mm | 2mm | 22mm | 25m |
| TPE U Channel 6mm x 23.5mm | 1mm to 3mm | 22mm | 25m |
| TPE U Channel 7mm x 24mm (this one) | 3mm | 22mm | 50m |
| TPE U Channel 7mm x 15mm | 3mm | shallower | 25m |
| TPE U Channel 8.5mm x 25mm | 4mm | deep | 25m |
Specification
| Property | Value | Test method / basis |
|---|---|---|
| Profile and dimensions | ||
| Profile | Round-bottom U channel with long parallel gripping arms (push-on edge protector) | – |
| Overall width | 7 mm | Nominal, manufacturer's profile drawing |
| Overall height | 24 mm | Nominal |
| Gripping arm length / slot depth | 22 mm | Nominal |
| Slot (inner) width | 3 mm | Nominal |
| Wall thickness | 2 mm | Nominal |
| Base thickness | 2 mm | Nominal (24 mm height less 22 mm arms) |
| Clamping range (fits panel / edge) | 3 mm only | Manufacturer's datasheet |
| Dimensional tolerance | Class E2 (cross-section), L2 (length), Quality Level 2 | ISO 3302-1 |
| Material properties | ||
| Material | Thermoplastic elastomer (TPE) | – |
| Hardness | 60 Shore A | Shore A durometer (ISO 48-4) |
| Weight | 99 g/m (about 4.95 kg per 50 m coil) | Manufacturer's datasheet |
| Service temperature (datasheet) | -25 °C to +70 °C | Manufacturer's datasheet: recommended design range |
| Temperature limits (technical data) | -40 °C to +90 °C | Manufacturer's published technical data; do not design to these as continuous |
| Resistance | Weathering, UV, chemicals, flex / bending fatigue, tear, abrasion | Manufacturer's description (qualitative) |
| Recyclability | 100% recyclable thermoplastic | Manufacturer's statement |
| Density, tensile strength, elongation, tear strength, compression set | Not published for this profile | Ask us if your specification needs them |
| Supply | ||
| Colour | Black | – |
| Unit of sale | One continuous 50 m coil | – |
| Price per metre | about £12.66 inc VAT | £632.94 ÷ 50 m |
| Part number | IP-TPEU-7X24X3-STD | – |
Material and compliance
This channel is extruded from a thermoplastic elastomer (TPE): a material that flexes and recovers like rubber, but which can be melted down and recycled, unlike vulcanised rubber. It keeps its clamping force in constant use and suits indoor and outdoor jobs.
- Dimensional tolerances: extruded to ISO 3302-1, cross-section class E2 and length class L2.
- Recyclable: the manufacturer states the material is 100% recyclable.
- No product approvals are stated for this profile: it is not offered as food-contact, drinking-water (WRAS) or fire-rated material. Ask us if you need an approved alternative.
How much do I need?
Add up every edge you want to cover and allow about 5% for trimming and joints. For example, 15 guard panels 1000mm x 600mm, trimmed on all four sides, need 15 x 3.2m = 48m. One 50m coil covers them with a little spare; for 20 such panels (about 67m with allowance) order two coils.
Fitting tips
- Deburr the edge and wipe it with a degreaser first: the arms grip much better on a clean, smooth edge
- Start at one end, open the lips onto the edge and press the channel home with your thumb as you work along; a rubber mallet helps on long runs
- Check the edge reaches the bottom of the slot, so all 22mm of each arm is gripping
- Do not stretch the trim as you fit it, or it will shrink back and open gaps at the ends
- Cut slightly over length with a sharp knife and push the ends together for a tight butt joint
Questions
Will it stay on without glue?
On a clean, deburred 3mm edge, yes in most cases. The 22mm arms grip the panel along their full depth, so it holds by friction alone and can be removed and refitted. For edges that are knocked often or vibrate, or for a permanent fit, run a thin bead of flexible adhesive in the slot.
Will it fit a 2mm or 4mm panel?
No. The slot and clamping range are 3mm only. For 1mm to 3mm sheet choose the TPE U channel 6mm x 23.5mm; for 4mm choose the 8.5mm x 25mm.
Why are the arms so long?
The 22mm arms touch far more of the panel than a standard U channel does. That spreads knocks away from the edge and gives a secure push-on fit, while the channel stays only 7mm wide (2mm on each face).
Can it go round corners and curves?
It follows gentle curves along its length. Because the arms are deep, it will not bend round a tight curve in the plane of the panel. For a 90° corner, mitre the ends and butt two lengths together, or cut a small V-notch out of both arms at the corner.
What temperatures can it take?
Design to -25°C to +70°C, the range on the manufacturer's datasheet; it is quoted as tolerating -40°C to +90°C at the extremes. Keep it off surfaces hotter than that.
Is it suitable for outdoor use?
Yes. The TPE resists weathering and UV, so it suits outdoor panels, steps, running boards and guards.
How do I cut and join it?
Cut square with a sharp knife or fine shears. Join lengths with a tight butt joint; a drop of flexible adhesive at the joint stops it opening up.
Can I use it on food equipment?
No food-contact approval is stated for this profile, so we do not recommend it where it may touch food. Ask us about an approved alternative.
Can I buy a shorter length or other colours?
This listing is a full 50m coil in black. For cut lengths or larger quantities, ask our team for a quote.
Need help choosing an edge trim or a seal? Call +44 1282 277786, email sales@industrial-polymers.co.uk or contact our team.
Product details
| SKU | IP-TPEU-7X24X3-STD |
|---|---|
| Weight | 10.91 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:TPE U Channel – 7mm x 24mm for 3mm Panels – 50m Coil