
Rubber & FoamSKU IP-TPEU-4X23X2-STD
TPE U Channel – 4mm x 23mm Deep Grip for 2mm Panels – 25m Coil
A slim black TPE U channel with unusually long gripping arms, made to protect and finish the edges of 2mm sheet: steel and aluminium panels, machine guards, glazing, acrylic and polycarbonate. It is only 4mm thick across the edge but 23mm tall, and the two arms grip 22mm down each face of the sheet. The arms are moulded angled inward, so they spring apart as the sheet goes in and clamp it along their full length. That wide grip holds by itself on most clean 2mm edges, so adhesive is usually not needed. Made from 60 Shore A thermoplastic elastomer and supplied as one continuous 25m coil.

At a glance
- Fits sheet and panels 2mm thick
- 4mm wide x 23mm high, 2mm slot with 22mm deep gripping arms, 1mm walls
- Low profile: adds only about 1mm to each face of the sheet
- Thermoplastic elastomer (TPE), 60 Shore A
- Temperature range -40°C to +90°C, indoors or outdoors
- Resists weathering, ageing, chemicals, flex fatigue, tearing and abrasion
- Cuts cleanly with a sharp knife; 100% recyclable thermoplastic
- 25m coil in black, about £18.72 per metre
Typical uses
- Capping the raw edges of 2mm steel or aluminium machine guards, covers and enclosure panels
- Protecting the edges of 2mm sheets during storage, handling and transport, and protecting people from the sharp edges
- Finishing the edges of thin glazing, acrylic and polycarbonate panels in screens, cabinets and displays
- Edge trim for running boards, steps and stair panels
- Bumper edging on furniture, shop-fitting and vending or kiosk panels
- Where sheets are stacked close together: the 4mm profile takes up little space
Which size do I need?
Measure the thickness of the edge you are covering and pick the channel whose slot matches it. Choose this one when you want a deep, wide grip on 2mm sheet with a very thin profile.
| U channel | Material | Fits edge thickness | Grip depth |
|---|---|---|---|
| TPE U Channel 4mm x 23mm (this one) | TPE, black | 2mm | 22mm |
| Deep U Channel 6 x 25mm | Neoprene, black | up to 2mm | deep |
| TPE U Channel 9mm x 13mm | TPE | 1mm to 2.5mm | shallow |
| TPE U Channel 8.5mm x 12mm | TPE | 1mm to 3mm | shallow |
| TPE U Channel 3mm x 7mm | TPE | 1mm | about 6mm |
Specification
| Property | Value | Test method / basis |
|---|---|---|
| Profile and dimensions | ||
| Profile | Round-bottom U channel with long, inward-angled gripping arms (push-on edge trim) | – |
| Overall width | 4 mm | Nominal, measured across the base |
| Overall height | 23 mm | Nominal |
| Slot (grip) width | 2 mm at the base, narrowing to approx. 0.5 mm at the lips when unfitted | Nominal at base; lip gap scaled from profile drawing |
| Gripping arm length / slot depth | 22 mm | Nominal |
| Wall thickness | 1 mm | Nominal |
| Base thickness | 1 mm | Nominal (23 mm height less 22 mm arms) |
| Fits panel / edge | 2 mm only | Manufacturer's clamping range |
| Dimensional tolerance | Class E2 (cross-section), L2 (length) | ISO 3302-1 |
| Material properties | ||
| Material | Thermoplastic elastomer (TPE) | – |
| Hardness | 60 Shore A | Shore A durometer (ISO 48-4) |
| Minimum service temperature | -40 °C | Manufacturer's data |
| Maximum service temperature | +90 °C | Manufacturer's data |
| Resistance | Weathering, ageing, general chemicals, flex fatigue, tear, abrasion | Manufacturer's description (qualitative) |
| Density, tensile strength, elongation, tear strength, compression set | Not published for this profile | Ask us if your specification needs them |
| Supply | ||
| Colour | Black | – |
| Unit of sale | One continuous 25 m coil | – |
| Part number | IP-TPEU-4X23X2-STD | – |
Material and compliance
This channel is extruded from a thermoplastic elastomer (TPE): a rubber-like material that flexes and recovers like rubber but, unlike vulcanised rubber, can be melted down and recycled. It stays elastic from -40°C to +90°C, resists weathering and ageing outdoors, and keeps its clamping force after repeated flexing.
- Dimensional tolerances: extruded to ISO 3302-1, cross-section class E2 and length class L2.
- Recyclable: the manufacturer states the material is 100% recyclable.
- No product approvals are stated for this profile: it is not offered as food-contact, drinking-water (WRAS) or fire-rated material. Ask us if you need an approved alternative.
How much do I need?
Add up every edge you want to cover and allow around 5% for trimming and joints. Example: twelve 2mm steel guard panels, each with two exposed 1m edges, need 24m, or about 25.2m with allowance. One 25m coil covers almost all of them; order two for the full set with spare.
Fitting tips
- Deburr the edge and wipe it with a degreaser first: the arms grip much better on a clean edge
- Start at one end, open the lips onto the edge and press the channel home with your thumb as you go; a rubber mallet helps on long runs
- Check the sheet reaches the bottom of the slot, so the full 22mm of each arm is gripping
- Cut slightly over length with a sharp knife and push the ends together for a tight butt joint
Questions
Will it stay on without glue?
On a clean 2mm edge, yes in most cases. The arms grip 22mm down each face and are angled inward, so they clamp along their whole length. For edges that are knocked often, or for a permanent fit, run a thin bead of flexible adhesive in the slot.
Will it fit 1.5mm or 3mm sheet?
It is made for 2mm only. On 1.5mm the arms still close on the sheet but the grip is weaker, so use adhesive. 3mm sheet is too thick and will force the arms apart; choose the TPE U channel 8.5mm x 12mm for 1mm to 3mm panels instead.
Why is it so tall for such a thin channel?
The 22mm arms give a far bigger gripping area than a standard U channel, so it holds securely without adhesive while adding only about 1mm to each face. That suits sheets that are stacked or fitted in tight spaces.
Can it go round corners and curves?
It follows gentle curves along its length. Because the arms are deep, it will not bend round a tight curve in the plane of the sheet; for a 90° corner, mitre the ends and butt two lengths together.
What temperatures can it take?
-40°C to +90°C. It stays flexible in winter outdoors and is fine on equipment that runs warm, but keep it away from hot surfaces above 90°C.
Is it suitable for outdoor use?
Yes. TPE resists weathering and ageing, so it can be used on outdoor panels, steps and running boards.
How do I cut and join it?
Cut square with a sharp knife or fine shears. Join lengths with a tight butt joint; a drop of flexible adhesive at the joint stops it opening up.
Can I use it on food equipment?
No food-contact approval is stated for this profile, so we do not recommend it where it may touch food. Ask us for an approved silicone channel.
Can I buy a shorter length or other colours?
This listing is a full 25m coil in black. For cut lengths or larger quantities, ask our team for a quote.
Need help choosing an edge trim or a seal? Contact our team.
Product details
| SKU | IP-TPEU-4X23X2-STD |
|---|---|
| Weight | 3.31 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:TPE U Channel – 4mm x 23mm Deep Grip for 2mm Panels – 25m Coil