
Rubber & FoamSKU IP-TPEU-6X23.5X1-STD
TPE U Channel Edge Trim – 6mm x 23.5mm for 1mm to 3mm Panels – 25m Coil
A slim, deep-grip black TPE U channel for capping and protecting panel edges from 1mm to 3mm thick: sheet steel and aluminium, machine guards, thin glazing, acrylic, board and furniture panels. It is 6mm across and 23.5mm tall, and its two 22mm gripping arms are moulded tapering inward, so the slot is 3mm wide at the base and closes to the lips. The arms spring open as the edge goes in and clamp it down their full length, which is why it normally holds without adhesive and can be pulled off and refitted. Made from 60 Shore A thermoplastic elastomer and supplied as one continuous 25m coil.

At a glance
- Fits panels and sheet edges 1mm to 3mm thick
- 6mm wide x 23.5mm high, with 22mm deep gripping arms and a 1.5mm wall
- Tapered inner slot (3mm at the base) clamps the edge along its full depth, so no adhesive is usually needed
- Push-on and removable: refit it as often as you need
- Thermoplastic elastomer (TPE), 60 Shore A
- Service temperature -40°C to +90°C, indoors or outdoors
- Good resistance to chemicals, flex fatigue, tearing and abrasion
- Cuts cleanly with a sharp knife; 100% recyclable thermoplastic
- 25m coil in black, about £17.22 per metre
Typical uses
- Capping the cut edges of 1–3mm steel or aluminium machine guards, covers and enclosure panels
- Protecting people from sharp sheet-metal edges, and protecting the sheets themselves in storage and transport
- Edging thin glazing, acrylic and polycarbonate panels in screens, cabinets and displays
- Edge trim for running boards, stair and step panels
- Bumper edging on furniture, shop-fitting and vending or kiosk panels
- Where sheets sit close together: at 6mm wide it adds only about 1.5mm to each face
Which size do I need?
Measure the thickness of the edge you are covering. Choose this channel when the edge is 1mm to 3mm thick and you want a deep, wide grip with a slim profile.
| U channel | Material | Fits edge thickness | Grip depth |
|---|---|---|---|
| TPE U Channel 6mm x 23.5mm (this one) | TPE, black | 1mm to 3mm | 22mm |
| TPE U Channel 4mm x 23mm | TPE, black | 2mm | 22mm |
| TPE U Channel 7mm x 24mm | TPE | 3mm | deep |
| TPE U Channel 8.5mm x 25mm | TPE | 4mm | deep |
| TPE U Channel 8.5mm x 12mm | TPE | 1mm to 3mm | shallow |
Specification
| Property | Value | Test method / basis |
|---|---|---|
| Profile and dimensions | ||
| Profile | Round-bottom U channel with long, inward-tapering gripping arms (push-on edge trim) | – |
| Overall width | 6 mm | Nominal, across the base |
| Overall height | 23.5 mm | Nominal |
| Gripping arm length / slot depth | 22 mm | Nominal |
| Inner slot width at base | 3 mm, tapering closed towards the lips when unfitted | Nominal, from manufacturer's profile drawing |
| Wall thickness | 1.5 mm | Nominal |
| Base thickness | 1.5 mm | Nominal (23.5 mm height less 22 mm arms) |
| Clamping range (fits panel / edge) | 1 mm to 3 mm | Manufacturer's clamping range |
| Dimensional tolerance | Class E2 (cross-section), L2 (length) | ISO 3302-1 |
| Material properties | ||
| Material | Thermoplastic elastomer (TPE) | – |
| Hardness | 60 Shore A | Shore A durometer (ISO 48-4) |
| Minimum service temperature | -40 °C | Manufacturer's technical data |
| Maximum service temperature | +90 °C | Manufacturer's technical data |
| Resistance | Chemicals, flex / bending fatigue, tear, abrasion | Manufacturer's description (qualitative) |
| Recyclability | 100% recyclable thermoplastic | Manufacturer's statement |
| Density, tensile strength, elongation, tear strength, compression set | Not published for this profile | Ask us if your specification needs them |
| Supply | ||
| Colour | Black | – |
| Unit of sale | One continuous 25 m coil | – |
| Price per metre | about £17.22 inc VAT | £430.59 ÷ 25 m |
| Part number | IP-TPEU-6X23.5X1-STD | – |
Material and compliance
This channel is extruded from a thermoplastic elastomer (TPE): a material that flexes and recovers like rubber, but which can be melted down and recycled, unlike vulcanised rubber. TPE can be compressed and stretched for long periods and still return to shape, so the arms keep their clamping force in constant use. It stays elastic from -40°C to +90°C.
- Dimensional tolerances: extruded to ISO 3302-1, cross-section class E2 and length class L2.
- Recyclable: the manufacturer states the material is 100% recyclable.
- No product approvals are stated for this profile: it is not offered as food-contact, drinking-water (WRAS) or fire-rated material. Ask us if you need an approved alternative.
How much do I need?
Add up every edge you want to cover and allow about 5% for trimming and joints. For example, ten guard panels 1000mm x 600mm, trimmed on all four sides, need 10 x 3.2m = 32m, or about 33.6m with allowance. That is two 25m coils, with spare.
Fitting tips
- Deburr the edge and wipe it with a degreaser first: the arms grip much better on a clean edge
- Start at one end, open the lips onto the edge and press the channel home with your thumb as you work along; a rubber mallet helps on long runs
- Check the edge reaches the bottom of the slot, so all 22mm of each arm is gripping
- Cut slightly over length with a sharp knife and push the ends together for a tight butt joint
Questions
Will it stay on without glue?
On a clean edge between 1mm and 3mm thick, yes in most cases. The tapered arms clamp the edge down their full 22mm, so it holds by grip alone and can be removed and refitted. For edges that are knocked often, or for a permanent fit, run a thin bead of flexible adhesive in the slot.
What panel thickness does it fit best?
Anything from 1mm to 3mm. It grips hardest at the thick end of that range (2–3mm), where the arms are opened furthest. On 1mm sheet it still holds, but add adhesive where the edge takes knocks. Thicker than 3mm will force the arms apart: choose the TPE U channel 8.5mm x 25mm for 4mm panels.
Why are the arms so long?
The 22mm arms touch far more of the panel than a standard U channel does. That gives a secure push-on fit without adhesive, while the channel stays only 6mm wide.
Can it go round corners and curves?
It follows gentle curves along its length. Because the arms are deep, it will not bend round a tight curve in the plane of the panel. For a 90° corner, mitre the ends and butt two lengths together, or cut a small V-notch out of both arms at the corner.
What temperatures can it take?
-40°C to +90°C. It stays flexible on outdoor equipment in winter and copes with machines that run warm. Keep it off surfaces hotter than 90°C.
Is it suitable for outdoor use?
Yes. The TPE is suitable inside and outside, so it can be used on outdoor panels, steps and running boards.
How do I cut and join it?
Cut square with a sharp knife or fine shears. Join lengths with a tight butt joint; a drop of flexible adhesive at the joint stops it opening up.
Can I use it on food equipment?
No food-contact approval is stated for this profile, so we do not recommend it where it may touch food. Ask us about an approved silicone or food-grade TPE channel.
Can I buy a shorter length or other colours?
This listing is a full 25m coil in black. For cut lengths or larger quantities, ask our team for a quote.
Need help choosing an edge trim or a seal? Call +44 1282 277786, email sales@industrial-polymers.co.uk or contact our team.
Product details
| SKU | IP-TPEU-6X23.5X1-STD |
|---|---|
| Weight | 5.51 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:TPE U Channel Edge Trim – 6mm x 23.5mm for 1mm to 3mm Panels – 25m Coil