
Rubber & FoamSKU IP-TPEU-9X20X3-STD
TPE Square U Channel – 9mm x 20mm for 3mm Panels – 25m Coil
A tall, heavy-walled square U channel for capping the raw edges of 3mm sheet. The profile is 9mm wide and 20mm high, with a 3mm parallel slot running a full 17mm deep. The walls and base are each a solid 3mm thick, so the trim takes knocks and pressure without crushing, while the long 17mm arms clamp a deep band of each face and usually need no adhesive. It is extruded from black 60 Shore A thermoplastic elastomer (TPE), supplied as one continuous 25m coil, and held in stock.

At a glance
- Fits sheet and panel edges 3mm thick
- 9mm wide x 20mm high, 3mm slot 17mm deep
- Uniform 3mm walls and base: about as rigid and crush-resistant as a trim this size gets
- Deep 17mm gripping arms hold each face, so glue is rarely needed
- Flat, square 9mm top gives a bold, protective finished edge
- 60 Shore A TPE: resists UV, weathering, chemicals and repeated flexing
- Cuts cleanly with a knife; fully recyclable thermoplastic
- Black, 25m coil, about £21.01 per metre
Typical uses
- Capping sharp edges on 3mm sheet-metal machine guards, covers and enclosure panels
- Edge finish on 3mm glazing, acrylic and polycarbonate screens
- Running boards, steps and stair-edge panels where a knock-resistant edge matters
- Vending machine, kiosk and display cabinet panels
- Furniture and shelving panels
- Protecting sheet stock edges during handling and transport

Which size do I need?
Measure the edge you want to cover and match it to the slot. A square U channel should fit the panel snugly: too thin and it sits loose, too thick and it splays the arms. Several trims fit 3mm sheet; they differ in how tall the trim is and how deep it grips.
| U channel | Fits edge thickness | Choose it when |
|---|---|---|
| TPE Square U Channel 6mm x 12mm | 2mm | Your sheet is 2mm |
| TPE Square U Channel 7mm x 12mm | 3mm | You want a compact, low-profile trim on 3mm sheet |
| TPE Square U Channel 7mm x 18mm | 3mm | You want a deep grip with a narrower 7mm face |
| TPE Square U Channel 9mm x 17mm | 3mm | You want a similar heavy trim on a 50m coil |
| TPE Square U Channel 9mm x 20mm (this one) | 3mm | You want the deepest 17mm grip and 3mm walls on a 25m coil |
| TPE Square U Channel 8mm x 12mm | 4mm | Your sheet is 4mm |
| TPE Square U Channel 9mm x 16mm | 5mm | Your sheet is 5mm |
Specification
| Property | Value | Test method / source |
|---|---|---|
| Profile and dimensions | ||
| Profile | Square-section U channel (push-on edge trim) | – |
| Overall width | 9.0 mm | Nominal, ISO 3302-1 class E2 |
| Overall height | 20.0 mm | Nominal, ISO 3302-1 class E2 |
| Slot width | 3.0 mm, parallel sides | Nominal |
| Slot depth (gripping arm length) | 17.0 mm | Nominal |
| Wall thickness | 3.0 mm each side | Nominal |
| Base thickness under slot | 3.0 mm | Nominal (20 mm height less 17 mm arms) |
| Fits edge / panel (clamping range) | 3 mm only | Manufacturer datasheet |
| Dimensional tolerance | Cross-section class E2, length class L2 (quality level 2) | ISO 3302-1 |
| Weight | 141 g per metre, approx. 3.5 kg per 25 m coil | Manufacturer datasheet |
| Material | ||
| Material | Thermoplastic elastomer (TPE) | – |
| Hardness | 60 Shore A | Shore A durometer (ISO 48-4) |
| Working temperature | -25 °C to +70 °C | Manufacturer datasheet (a wider -40 °C to +90 °C is also quoted; we list the more cautious datasheet figure) |
| Environmental resistance | UV, weathering, chemicals, flex fatigue; good tear and abrasion resistance | Manufacturer data |
| Density, tensile strength, elongation, tear, compression set | Not published for this profile; ask us if you need them | – |
| Supply | ||
| Colour | Black | – |
| Unit of sale | One continuous 25 m coil | – |
| Availability | Held in stock | – |
Material and compliance
TPE is a rubber-like material that is processed like a plastic. It gives a consistent, rubbery feel, needs no vulcanising, and can be recycled at end of life.
- Weathering: stable in sunlight and outdoor conditions, and resists ageing
- Chemical resistance: stands up to water, mild cleaning agents and general workshop exposure
- Tolerances: extruded to ISO 3302-1, the standard tolerance scheme for rubber and elastomer extrusions
No food-contact, potable-water (WRAS), REACH/RoHS or fire-rating approval is claimed for this profile. If you need a declaration for your file, contact our team.

How much do I need?
Total the length of every edge you want to cover and add about 5% for trimming. Example: twenty 600mm x 400mm guard panels trimmed on all four sides have 40m of edge, or 42m with allowance, so order two 25m coils. Ten of the same panels (20m, 21m with allowance) fit on one coil.
Fitting tips
- Check the panel really is 3mm: thinner sheet will sit loose, thicker sheet will splay the arms
- Deburr the edge and wipe it free of oil and grease before fitting
- Start at one end and press the channel on with your thumb as you work along; a soft mallet helps on long runs, as the 3mm walls are stiff
- Push the channel down until the panel edge seats against the base of the slot
- Cut slightly over length with a sharp knife and push the ends together for a tight joint
- Ease it round gentle curves; this tall, stiff section is best mitred or V-notched in the base at tight corners
- For a permanent or vibration-proof fit, add a thin bead of sealant or adhesive in the slot
Questions
What edge thickness does it fit?
It is made for 3mm edges only. For 2mm sheet choose the 6mm x 12mm square U channel; for 4mm sheet choose the 8mm x 12mm.
How does it differ from the other 3mm square U channels?
This is the tallest and heaviest of them: 20mm high with 17mm arms and 3mm walls, so it grips deepest and protects best. The 7mm x 12mm is a slimmer, low-profile option, and the 9mm x 17mm is a similar heavy trim sold on a 50m coil.
Does it need glue?
Not usually. The 17mm sides grip a clean 3mm edge firmly on their own. Add adhesive only where there is heavy traffic, vibration, or you want it permanent.
Can it go round curves and corners?
It follows gentle curves. Because the section is tall and stiff, mitre the channel or notch the base for a tight 90° corner so it folds neatly.
Is it suitable outdoors, and what temperatures can it take?
Yes. TPE resists UV and weathering. The datasheet working range is -25°C to +70°C, so keep it away from ovens, exhausts and other hot surfaces.
How do I cut and join it?
A sharp knife or fine-toothed saw gives a clean square cut. Butt the ends tightly; for a sealed joint, add a dab of instant adhesive.
What is it made of?
Black thermoplastic elastomer (TPE) at 60 Shore A: firm enough to protect, soft enough to push on by hand, and fully recyclable.
Is it food-safe?
No food-contact approval is claimed for this black TPE trim.
How accurate are the dimensions?
The cross-section is extruded to ISO 3302-1 class E2, so allow a few tenths of a millimetre either way on the nominal sizes.
When will it ship?
This trim is held in stock and ships in line with the dispatch times shown on this page.
Can I buy a shorter length?
This listing is a full 25m coil in black. For cut lengths or larger quantities, ask our team for a quote.
Need help choosing an edge trim? Contact our team on +44 1282 277786 or sales@industrial-polymers.co.uk.
Product details
| SKU | IP-TPEU-9X20X3-STD |
|---|---|
| Weight | 7.94 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:TPE Square U Channel – 9mm x 20mm for 3mm Panels – 25m Coil