
Rubber & FoamSKU IP-IPEDP-11X9.5-9
EPDM D Section Door Seal – 11mm x 9.5mm – Cut Lengths
Price shown updates with the option you pick.
This EPDM D section door seal 11mm x 9.5mm pushes onto a 2mm panel edge and gives a hollow, compressible D bulb that closes the gap against a door, hatch or window frame, keeping out water, draughts and dust while cushioning light knocks. It is sold as one continuous length, from 9m up to a full 30m coil.
At a glance
- Profile: 11mm wide x 9.5mm high hollow D bulb with a 2mm side channel
- Fits 2mm panel or flange edges with no adhesive needed
- Black EPDM rubber, 65-75 Shore A
- Strong weather and UV resistance for indoor or outdoor door seal and weather seal jobs
- Good heat, cold and abrasion resistance and resists repeated flexing
- Supplied as one unbroken length: 9m to 29m, or a full 30m coil
- Cuts cleanly with a sharp knife; 100% recyclable
Typical uses
- Door and window seals on classic cars and caravans
- Bus, coach and rail vehicle panels and service hatches
- Marine lockers and deck hatches
- Aviation ground equipment panels and access doors
- General 2mm panel edge sealing in workshops and fabrication
Which one do I need?
| Your job | Best choice |
|---|---|
| 2mm panel edge, hollow D bulb sealing against a frame | This EPDM D section 11mm x 9.5mm |
| 1mm to 2mm panel edge, bulb on top of a self-grip clip | EPDM self-grip door seal 15.5mm x 10mm |
| No panel edge to grip, stick-on seal needed | TPE sponge D profile 10mm x 8mm, adhesive backed |
| Larger gap, softer sponge bulb, stick-on | EPDM sponge boot seal 12mm x 17mm |
Technical drawing
Specification
| Product | D section door seal with side channel |
| Material | EPDM rubber |
| Profile size | 11mm x 9.5mm |
| To fit panel | 2mm |
| Hardness | 65-75 Shore A |
| Colour | Black |
| Unit of sale | One continuous length per order, 9m to 29m, or a full 30m coil |
How much do I need?
Measure every edge the seal will run along and add about 5% for trimming at the corners. Example: a steel cabinet door 1.8m high x 0.9m wide needs 2 x 1.8m + 2 x 0.9m = 5.4m, plus 5% = 5.7m, so the 9m minimum length covers it with spare. Three identical doors need about 17m, so order 17m or 18m. If you need close to 30m, the full 30m coil is priced lower than most of the long cut lengths, so it is usually the better buy.
Fitting tips
- Clean the 2mm edge and remove burrs so the channel seats fully.
- Start at the bottom or least visible corner and push the channel on by hand, working along the edge.
- Point the D bulb towards the surface it seals against so it compresses as the door closes.
- Do not stretch the seal while fitting; lay it on relaxed or it may shrink back and leave gaps.
- Cut with a sharp knife in one stroke so the hollow bulb is not crushed; butt the two ends tightly together.
Complete your project
- EPDM Self-Grip Door Seal – 15.5mm x 10mm for 1mm to 2mm Panels
- EPDM Self-Grip Door Seal – 12.5mm x 8mm
- TPE Sponge D Profile – 10mm x 8mm Adhesive Backed
Questions
What panel thickness does this D section seal fit?
The side channel is made for 2mm panels and flanges. For 1mm to 2mm edges, the self-grip door seal 15.5mm x 10mm is a better fit.
Can this EPDM door seal be used outdoors?
Yes. EPDM has excellent weathering and UV resistance, so it suits exterior doors, vehicles and marine hatches as well as indoor cabinets.
Is the D bulb solid or hollow?
Hollow. The hollow bulb compresses when the door closes, which gives a tighter seal over small gaps and absorbs light impacts.
Do I need glue to fit it?
Normally no. The channel pushes onto the 2mm edge. On a very smooth or loose-fitting edge a few dots of a rubber-compatible contact adhesive can stop it creeping.
Can I buy less than 9m?
No, 9m is the shortest length. Each order is supplied as one continuous length up to a full 30m coil.
Need help choosing a seal? Contact our team and we will help you pick the right profile.
Product details
| SKU | IP-IPEDP-11X9.5-9 |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM D Section Door Seal – 11mm x 9.5mm – Cut Lengths