
Rubber & FoamSKU IP-EPDMD-114X95-STD
EPDM Delta D Fender – 114mm x 95mm – 3m Length
This EPDM delta D fender is a 114mm x 95mm hollow rubber buffer for loading bays, quaysides, jetties and vehicle-facing walls, giving a deep, firm cushion against repeated impacts. It is sold as one 3m length that you can fit whole or cut to suit.
At a glance
- Hollow delta D fender profile, 114mm wide at the base and 95mm high
- Large 55mm x 53mm cavity that compresses to absorb impact energy
- Wide flat base for bolting, bonding or fitting in a retaining channel
- Black EPDM rubber, 70 Shore A, with good weather, UV and ozone resistance
- Heavy-duty section at about 15kg per metre
- Supplied as a single 3m length
Typical uses
- Loading bay and dock edge protection where lorries reverse in
- Quay, jetty and pontoon edges for workboats and service vessels
- Car park walls, columns and ramp edges
- Warehouse walls and racking ends exposed to forklift contact
- Sides of trailers, skips and site equipment as a rubber bumper strip
Which one do I need?
| Delta D fender | Best for |
|---|---|
| 80mm x 70mm | Light vehicle and small-boat protection, low walls |
| 110mm x 95mm | General dock and loading bay edges |
| 114mm x 95mm EPDM (this item) | Heavier, weather-exposed docks and quays in a single 3m length |
| 150mm x 130mm | Heavy commercial berths and large vehicles |
Technical drawing
Specification
| Profile | Hollow delta D fender |
| Outer size | 114mm wide x 95mm high |
| Cavity | 55mm wide x 53mm high |
| Material | EPDM rubber |
| Hardness | 70 Shore A |
| Weight | Approx. 15kg per metre |
| Colour | Black |
| Unit of sale | One 3m length |
How much do I need?
Measure each edge to be protected and divide by 3m, rounding up. For example, a 7.5m dock edge needs three 3m lengths (9m), leaving 1.5m spare to cut a short buffer for a nearby column or door frame.
Fitting tips
- Fix through the flat base with marine-grade or masonry bolts and large washers, spacing fixings evenly along the length.
- Counterbore or slot the base so bolt heads sit below the rubber face and cannot touch vehicles or hulls.
- Leave a small gap between butted lengths to allow for expansion in hot weather.
- Cut square with a fine-toothed saw, supporting the section so the hollow does not crush.
Complete your project
- Hollow TPE Delta D Fender – 80mm x 70mm – 10m Coil
- TPE Delta D Fender – 110mm x 95mm – 2 x 5m Pack
- Hollow TPE Delta D Fender – 150mm x 130mm – Pack of 2 x 5m
Questions
Can I cut the 3m length?
Yes. The EPDM cuts cleanly with a fine-toothed saw or a sharp blade, so you can make shorter buffers for columns, doors or corners.
Is this rubber dock fender suitable outdoors and near sea water?
Yes. EPDM is chosen for its resistance to weather, UV, ozone and water, so it suits exposed docks, quays and marine edges.
How is the delta D fender fixed?
Most users bolt through the wide flat base. It can also be held in a suitable retaining channel or bonded with a rubber-compatible adhesive on smooth surfaces.
Why choose a hollow fender rather than a solid one?
The large cavity lets the profile deflect and spread the load, giving a softer, more forgiving impact than a solid rubber block of the same size.
Need help choosing a fender? Contact our team and we will advise.
Product details
| SKU | IP-EPDMD-114X95-STD |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Delta D Fender – 114mm x 95mm – 3m Length