
Rubber & FoamSKU IP-EPDMD-12.5X12.5-7M
EPDM Sponge D Section – 12.5mm x 12.5mm, Plain Base – 7m to 50m or 25m Coil
Price shown updates with the option you pick.
A soft, hollow D-section seal in black EPDM sponge, 12.5 mm wide and 12.5 mm high, with a flat 12.5 mm base and a 6.2 mm round hollow core. Cut to any whole length from 7 m to 50 m, or buy the full 25 m coil. The arched crown squeezes down into the hollow as a door, lid or hatch closes, so it seals uneven gaps of roughly 7.5 to 10 mm with little closing force. It is also a recognised replacement for the classic MG and Jaguar sponge D seal (OE part BD 2159) and works as a soft bump or edge strip.
At a glance
- Size: 12.5 mm wide × 12.5 mm high, with a Ø6.2 mm round hollow core
- Material: expanded (sponge) EPDM, very soft at 40° Shore OO
- Fixing: plain flat base: bond it with a contact adhesive suited to EPDM sponge. Want peel-and-stick? See the self-adhesive (SAB) version of this seal
- Outdoors: rated excellent for ozone, weather and UV; flexible at -40 °C
- Lengths: 7 m to 24 m at £24.33 per metre; the full 25 m coil at £486.75 (£19.47 per metre); 26 m to 50 m at £19.47 per metre
- Stock: held in stock in the UK and dispatched from stock
Typical uses
- Door, boot and bonnet seals on classic cars: replaces the MG and Jaguar sponge D seal, OE part BD 2159
- Door and lid seals on electrical enclosures, control cabinets and kiosks
- Hatch, access panel and inspection door seals on buses, caravans, trailers and rail vehicles
- Glazing, closure and weather strips
- Soft edging and light impact protection on panels and equipment
- Gaskets and small expansion-joint fillers; thin cables can run through the hollow core
Technical drawing

Specifications
| Property | Value | Test method / basis |
|---|---|---|
| Profile type | Hollow D section on a flat, plain base | Manufacturer's profile drawing |
| Overall width (across the base) | 12.5 mm | Nominal; tolerance BS 3734 Class E3 |
| Overall height (base to crown) | 12.5 mm | Nominal; tolerance BS 3734 Class E3 |
| Hollow core | Ø6.2 mm, round | Manufacturer's product description (their drawing shows it a little smaller) |
| Height of the straight sides | About 8.8 mm, then an arched crown | Scaled from the manufacturer's drawing; not separately stated |
| Hollow centre above the base | About 6.2 mm | Scaled from the manufacturer's drawing; not separately stated |
| Crown wall thickness | About 3.2 mm | Worked out from the stated sizes and the hole position; not separately stated |
| Side wall thickness | About 3.15 mm | Worked out from 12.5 mm width and Ø6.2 mm core; not separately stated |
| Base thickness under the core | About 3.1 mm | Worked out as above; not separately stated |
| Fixing | Plain base, no adhesive tape: bond with a contact adhesive suited to EPDM sponge | Manufacturer's drawing and product page |
| Material | Expanded (sponge) EPDM | Manufacturer datasheet |
| Colour | Black | - |
| Hardness | 40° Shore OO | Shore OO durometer scale (for soft foams); test standard not stated |
| Density | 0.5 to 0.9 g/cm³ | Manufacturer datasheet; method not stated |
| Weight | 80 g per metre: about 2.0 kg per 25 m coil | Manufacturer figure |
| Water absorption | 5% maximum | Manufacturer datasheet; method not stated |
| Compression set | 50% (product page, 22 h) · 25% maximum (datasheet, 24 h recovery) | Manufacturer figures; test temperature and standard not stated. The two sources differ, so plan on the higher figure |
| Heat ageing | ±30% change after 7 days at 70 °C | Manufacturer datasheet; property measured not stated |
| Low-temperature flexibility | Pass at -40 °C | Manufacturer datasheet |
| Ozone resistance | Excellent | Manufacturer rating |
| Weather resistance | Excellent | Manufacturer rating |
| UV light resistance | Excellent | Manufacturer rating |
| Mould growth resistance | Very good | Manufacturer rating |
| Service temperature range | Not stated for this profile. About -40 °C to +100 °C (typical for EPDM sponge, not tested on this profile) | Tested points stated: flexible at -40 °C, aged at +70 °C |
| Tensile strength, elongation at break, tear strength | Not stated for this profile | Ask us if you need them |
| Dimensional tolerance | BS 3734 Class E3 (extruded sponge) | BS 3734 |
| Supplied length | 7 m to 24 m in one continuous piece; full 25 m coil; 26 m to 50 m as a 25 m coil plus the balance cut from a second coil | Manufacturer coil length 25 m |
| Price per metre | £24.33/m inc VAT for 7–24 m; £19.47/m inc VAT for the 25 m coil (£486.75) and for 26–50 m | - |
Sponge sections are flexible, so treat all sizes as nominal. The manufacturer states the core as 6.2 mm; on its drawing the core looks closer to 5 mm. Either way the walls are around 3 mm thick.
Materials and compliance
Expanded (closed-cell sponge) EPDM. The manufacturer describes the profile as air and watertight, with good UV and weather resistance, and EPDM as resistant to ozone, heat, steam, ketones and dilute acids and alkalis, with good electrical insulation. Like all EPDM it is not suited to oils, fuels or solvents.
The manufacturer does not state any food-contact (FDA, EC 1935/2004), drinking-water (WRAS), REACH, RoHS or fire-rating approval for this profile, so we do not claim any. If your job needs a certified material, ask us before you order.
How it fits

- Measure the closed gap. It should be smaller than 12.5 mm so the D is squeezed. About 7.5 to 10 mm (20 to 40% squeeze) is a good starting point; this is our guidance, not a manufacturer figure.
- Check the landing. The face you bond to should be at least 12.5 mm wide.
- Clean and dry. Degrease with isopropyl alcohol and let it dry.
- Bond the base. Use a contact adhesive suited to EPDM sponge on the flat base. Lay the strip without stretching it, or it will shrink back from the ends.
- Corners and joins. Ease it round gentle corners; for sharp corners cut and butt the ends tightly, or mitre them. Put joins where water will not sit.
How much do I need?
Add up the edges to be sealed and allow about 5% for trimming. Example: a classic car with two doors about 1.0 m × 0.9 m needs 2 × 2 × (1.0 + 0.9) = 7.6 m; add 5% and choose 8 m. From 20 m upwards the full 25 m coil costs about the same or less than a cut length, so pick the coil.
Which size do I need?
| Profile | Size (W × H) | Supplied as |
|---|---|---|
| EPDM sponge D section | 10 × 8 mm | Cut length or 100 m coil, plain base |
| EPDM sponge D section | 12 × 10 mm | 75 m coil |
| EPDM sponge D section (this item) | 12.5 × 12.5 mm | 7–50 m or 25 m coil, plain base |
| EPDM sponge D section, self-adhesive (SAB) | 12.5 × 12.5 mm | Same profile with an adhesive-backed base |
| EPDM D section door seal | 12.5 × 9.5 mm | Per metre, lower profile |
Questions
How is it sold?
Choose a length from 7 m to 24 m and it is cut as one continuous piece at £24.33 per metre. The full 25 m coil is £486.75, and 26 m to 50 m is £19.47 per metre (a full coil plus the balance). The minimum length is 7 m. For more than 50 m, add several coils or ask us.
What gap will it seal?
Any closed gap below its 12.5 mm height. Aim for roughly 7.5 to 10 mm closed. For gaps of about 7 mm or less the 10 × 8 mm or 12 × 10 mm sponge D closes more easily.
Will it fit my MG or Jaguar?
The manufacturer lists it as a replacement for the MG and Jaguar sponge D seal, OE part BD 2159. Compare it with your old seal or the drawing above before you cut it.
Is it self-adhesive?
No. The base is plain, so bond it with a contact adhesive suited to EPDM sponge. If you want peel-and-stick, choose the self-adhesive (SAB) 12.5 × 12.5 mm version.
How do I cut and join it?
A sharp craft knife or scissors gives a clean square end. Butt the ends tightly; for a fully sealed join, bond the ends with a rubber-compatible instant adhesive.
Can I use it outdoors?
Yes. The manufacturer rates its ozone, weather and UV resistance as excellent, and it absorbs no more than 5% water.
What temperatures can it take?
The manufacturer has tested it as flexible at -40 °C and heat-aged it at +70 °C, but does not state a full working range. EPDM sponge typically works from about -40 °C to +100 °C (typical for EPDM sponge, not tested on this profile).
Will it stand up to oil or fuel?
No. EPDM handles water, steam, weather and dilute acids and alkalis well but swells in oils, fuels and most solvents. Ask us for a neoprene or nitrile alternative.
Is it food-safe or WRAS approved?
No approvals are stated for this profile, so do not use it where certified food-contact or drinking-water material is required.
Can I run a cable through the hollow?
Yes, cables up to about 5 mm can be threaded through the 6.2 mm core, and the sponge gives them some weather protection. Leave the core empty if you need the full sealing squeeze.
Delivery and help
Held in stock and dispatched from the UK. Trade and quantity orders welcome. Not sure it is the right profile? Call +44 1282 277786 or email sales@industrial-polymers.co.uk and we will check it for you.
Product details
| SKU | IP-EPDMD-12.5X12.5-7M |
|---|---|
| Weight | 1.46 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Sponge D Section – 12.5mm x 12.5mm, Plain Base – 7m to 50m or 25m Coil