
Rubber & FoamSKU IP-TPEUC-3X9-BLACK
TPE Square U Channel – 3mm x 9mm for 1mm Edges – 25m Coil
A slim, firm push-on edge trim for the thinnest edges in the workshop. This square-section U channel is just 3mm across and 9mm tall, with a 1mm slot that grips 1mm sheet metal, thin glass, acrylic and laminate. The tall sides give it a deep hold on the edge, so on clean 1mm material it stays put without adhesive, and it can be pulled off and refitted. Made from black TPE (thermoplastic elastomer) at 60 Shore A, it is supplied as one continuous 25m coil and is held in stock.
At a glance
- Fits edges 1mm thick
- 3mm wide x 9mm high, 1mm slot about 8mm deep, 1mm walls and base
- Firm 60 Shore A TPE: holds its shape on thin sheet yet still follows curves
- Resists UV, weathering and repeated flexing, so it suits indoor and outdoor kit
- Cuts cleanly with a knife or snips; fully recyclable thermoplastic
- Black, 25m coil, about £17.35 per metre
Typical uses
- Covering sharp edges on 1mm sheet-metal guards, covers and enclosure panels
- Edge finish for vending machine, kiosk and cabinet panels
- Cushioning thin glass, acrylic and polycarbonate in display and shop-fitting work
- Protecting furniture, shelving and stair-edge panels made from thin sheet
- Trim on running boards and light vehicle or trailer panels
- Temporary edge protection on sheet stock during handling and transport
Which size do I need?
Measure the edge you want to cover and choose the slot that matches it.
| U channel | Fits edge thickness |
|---|---|
| TPE Square U Channel 3mm x 9mm (this one) | 1mm |
| Silicone Round U Channel 3mm x 5mm (food-contact, high-temperature) | 1mm |
| TPE U Channel Edge Trim 9mm x 13mm | 1mm to 2.5mm |
| TPE U Channel 8.5mm x 12mm | 1mm to 3mm |
| TPE Square U Channel 22mm x 12mm | 8mm to 10mm |
Specification
| Property | Value | Test method |
|---|---|---|
| Profile and dimensions | ||
| Profile | Square-section U channel (push-on edge trim) | – |
| Overall width | 3 mm | Nominal, ISO 3302-1 class E2 |
| Overall height | 9 mm | Nominal, ISO 3302-1 class E2 |
| Slot width | 1 mm | Nominal |
| Slot depth | approx. 8 mm | Scaled from profile drawing |
| Wall and base thickness | 1 mm | Nominal |
| Fits edge / panel | 1 mm | – |
| Dimensional tolerance | Cross-section class E2, length class L2 | ISO 3302-1 |
| Weight | approx. 23 g per metre, approx. 0.58 kg per 25 m coil | Manufacturer data |
| Material | ||
| Material | Thermoplastic elastomer (TPE) | – |
| Hardness | 60 Shore A | Shore A durometer (ISO 48-4) |
| Working temperature | -25 °C to +70 °C | Manufacturer data |
| Environmental resistance | UV, weathering, flex fatigue; good tear and abrasion resistance | Manufacturer data |
| Supply | ||
| Colour | Black | – |
| Unit of sale | One continuous 25 m coil | – |
| Availability | Held in stock | – |
Technical drawing

Dimensions in mm. Need a copy of this drawing for your files? Ask our team.
Material and compliance
This trim is extruded from a thermoplastic elastomer: a rubber-like material that is processed like a plastic. That gives it a consistent, rubbery feel with no vulcanising agents, and it can be recycled at end of life.
- Weathering: stable in sunlight and outdoor conditions, so it does not go brittle or crack in normal outdoor use
- Chemical resistance: stands up to water, mild cleaning agents and general workshop exposure
- Tolerances: extruded to ISO 3302-1, the standard tolerance scheme for rubber and elastomer extrusions
No food-contact, potable-water (WRAS) or fire-rating approval is claimed for this profile. For food equipment, see our food-contact silicone U channel. If you need a declaration for your file, contact our team.
How much do I need?
Total the length of every edge you want to cover and add about 5% for trimming. Example: 12 guard panels, each with 1.8m of exposed edge, need 21.6m, or about 22.7m with allowance, so one 25m coil covers the job.
Fitting tips
- Deburr the edge and wipe it free of oil and dust before fitting
- Start at one end and press the channel on with your thumb as you work along
- Cut slightly over length with a sharp knife or snips and push the ends together for a tight joint
- Round a curve by easing the trim on gradually; on a sharp corner, notch the base or butt two lengths
- For a permanent or vibration-proof fit, add a thin bead of sealant or adhesive in the slot
Questions
What edge thickness does it fit?
It is made for 1mm edges. It will grip slightly thinner material too, but below about 0.8mm add a little adhesive so it cannot slide off.
Does it need glue?
Not usually. The 9mm-tall sides grip a clean 1mm edge firmly on their own. Use adhesive only where there is heavy vibration or you want it permanent.
Can it go round curves and corners?
Yes. Although it is firm, it follows gentle curves easily. For a tight 90° corner, cut a small V-notch in the base or join two lengths at the corner.
Is it suitable outdoors?
Yes. TPE resists UV and weathering. Its rated working range is -25°C to +70°C, so keep it away from hot surfaces such as ovens or exhausts.
Is it food-safe?
No food-contact approval is claimed for this black TPE trim. For food machinery, choose our food-contact silicone U channel for 1mm edges.
How accurate are the dimensions?
It is extruded to ISO 3302-1 class E2 for the cross-section, so allow a few tenths of a millimetre either way on the nominal sizes.
When will it ship?
This trim is held in stock, so it ships in line with the dispatch times shown on this page.
Can I buy a shorter length or a different colour?
This listing is a full 25m coil in black. For cut lengths, larger quantities or other profiles, ask our team for a quote.
Need help choosing an edge trim? Contact our team.
Product details
| SKU | IP-TPEUC-3X9-BLACK |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:TPE Square U Channel – 3mm x 9mm for 1mm Edges – 25m Coil